Vacuum Regulation Monitoring Vacuum Components For Sale In Washington

Model 100 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 150 CFM ASME and features direct sensing that is sensitive to 0.1" hg of change in vacuum pressure.

The Digimet 3000 is a 5-key, hand-held, battery operated, microprocessor-based meter which reads a variety of vacuum and pulsation characteristics in the milking system. DOS and Windows software is included to allow numerical and waveform data to be named,...

Vacuum gauges assure accurate readings of line vacuum and provide constant monitoring for maximum herd protection. Dual scale, Hg and KPA. Glycerine fill assures accuracy by providing a cushion against vibration.

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

Part number "353-06" on schematic diagram.

The MKII Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 150 CFM ASME and features direct sensing that is sensitive to 0.1" hg of change in vacuum pressure.

Fits Sentinel 100, 350, 500 Vacuum controllers. Part number "348-33" on schematic diagram.

The Peacekeeper for the Mark II vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the noise created by air flow into the controller.

Includes cables, paper roll, and AC transformer. 4” x 4” x 2” unit prints characters and graphics on a strip of paper.

Repair Kit for Fullwood/BouMatic (blue) Vacuum Regulator contains gaskets, O-rings and filters.

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

The Peacekeeper for the model M100 vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the noise created by air flow into the controller.

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

Safety Valve for Stabilvac Seperate styles.

CTA Pumps come complete with Silencer, Oiler, Pulley and zinc terminal valve. There is about 4 CFM needed per cow. Pump performance, or CFM, varies according to ambient temperature, humidity, air pressure, elevation and many other factors.

At sea level at a temperature of 68F , with a 3HP motor, the RPM of this model is 900 and the CFM is 32. CTA Pumps come complete with Silencer, Oiler, Pulley and zinc terminal valve.

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

Replacement Lid Gasket for Pre-Filters 160201, 160206, 160208, 160237 and 160238

Straight Brass Stall Cock; 3/8" thread.

Pre-Air Filters are packaged in 350-lb. .Vacum Pre-Air Filter with 4" pump connection for 4" single or duble vacuum line . A plug is included to seal off the unneeded outlet in single configuration.

With dusty conditions there is only one way to guarantee that pulsators get the clean air that enables them to function at peak efficiency. Includes 2 each nipple adapter no. 160218, black transflow hose, 90 degree elbow and one pulsator cover no.160222.

Features green plastic body with replaceable foam filter. Our low-cost, quick-mount Fresh Air Filter is attached directly to 3” PVC pipe and can handle six pulsators.

Part number "348-28" on schematic diagram.

Pre-Air Filters are packaged in 350-lb. Vacum Pre-Air Filter with 6" pump connection for 4" single or duble vacuum line . A plug is included to seal off the unneeded outlet in single configuration.

Relief Valve for Sentinel Controllers models M350 and M500 protects against occurrences of high vacuum. For systems with CFM's over 250, two are recommended. Part number "348-17" on schematic diagram.

Replacement End Cap for 15" tank with one 3" inlet