Vacuum Regulation Monitoring Vacuum Components For Sale In North Carolina

This regulator is recommended for vacuum pumps from 35 to 70 cfm (1,000 to 2,000 liters/min) and will maintain vacuum from 11” to 15” Hg (36 to 50 kPa). The design allows for quick installation, and the unit can be cleaned and serviced in less than...

Replacement foam filter sold separately. Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the model M100 vacuum controller is a combination noise suppressor and air filter providing a large washable...

Part number "353-06" on schematic diagram.

Replacement foam filter sold separately. Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the Mark II vacuum controller is a combination noise suppressor and air filter providing a large washable...

Large Carrying Case can hold the Digimet Unit, the printer, battery pack, cables, instruction manual and accessories.

Part number "348-17" on schematic diagram. For systems with CFM's over 250, two are recommended. Relief Valve for Sentinel Controllers models M350 and M500 protects against occurrences of high vacuum.

Replacement Foam Filter for 173-02010 Vacuum Regulator. Two filters required.

Repair Kit for Fullwood/BouMatic (blue) Vacuum Regulator contains gaskets, O-rings and filters.

Featuring a serial port and a variety of additional internal features, the Digimet 3000 displays average, maximum, and minimum vacuum level, fluctuation level, pulsator ratio, pulses per minute, milk/rest ratio.

Replacement foam filter sold separately. Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the M350 and M500 vacuum controller is a combination noise suppressor and air filter providing a large washable...

Glycerine fill assures accuracy by providing a cushion against vibration. Vacuum gauges assure accurate readings of line vacuum and provide constant monitoring for maximum herd protection.

Straight Brass Stall Cock; 3/8" thread.

There is about 4 CFM needed per cow. CTA Pumps come complete with Silencer, Oiler, Pulley and zinc terminal valve. At sea level at a temperature of 68F, with a 2HP motor, the RPM of this model is 1100 and the CFM is 21.

There is about 4 CFM needed per cow. CTA Pumps come complete with Silencer, Oiler, Pulley and zinc terminal valve. At sea level at a temperature of 68F , with a 3HP motor, the RPM of this model is 900 and the CFM is 32.

Fits assemblies with 20 to 25 HP pump. Straight Silencer with 4" NPT. Extra quiet, glass-packed silencers, included with Kaeser Vacum Pump Assemblies, also may be ordered separately.

Angle Brass Stall Cock; 3/8" thread.

Nickel-Plated brass stall cocks have a large diameter passage, positive on/off and NPT thread. Fine quality--economically priced

Case of 4 gallons. Coburn Vacuum Pump Cleaner contains a rust inhibitor to protect the pump from rust and corrosion.

Fits assemblies with 30 or 40 HP pump. Straight Silencer with 6" NPT. Extra quiet, glass-packed silencers, included with Kaeser Vacum Pump Assemblies, also may be ordered separately.

Washguard motors meet all applicable UL and CSA standards. 3HP with a 7/8" shaft in a stainless steel finish, three phase, 145TC frame, 208-230/460 voltage, and 3600 RPM. They feature type 303 stainless steel shafts, drains in end shield, moisture-resistant...

• All Stainless Steel Screws. • 303 Stainless Steel Shaft. • Special Moisture Resistant Interior Coatings. • Dual Voltage 115/230. • Stainless Steel “Full Fact Nameplate.

Stabilvac Vacuum Relief Valve works over a range of 36 to 50 kPa (11" to 15" Hg) and has a capacity of 1400 liter/min. At 50 kPa (49 cfm at 15" Hg.)

Kaeser Pump Oil is a special synthetic oil especially recommended for Kaeser pumps. It requires changing much less often than ordinary petroleum-based oils.

Washguard motors meet all applicable UL and CSA standards. 2HP with a 7/8" shaft in a stainless steel finish, three phase, 145TC frame, 208-230/460 voltage, and 3600 RPM. They feature type 303 stainless steel shafts, drains in end shield, moisture-resistant...

Double-wall corrugated box with expanded polystyrene corner pads. Vacum Pre-Air Filter with 6" pump connection for 6" single or duble vacuum line . Pre-Air Filters are packaged in 350-lb.

• All Stainless Steel Screws. • 303 Stainless Steel Shaft. • Special Moisture Resistant Interior Coatings. • Dual Voltage 115/230. • Stainless Steel “Full Fact Nameplate.

Fits assemblies with 15 HP pump. Straight Silencer with 3" NPT. Extra quiet, glass-packed silencers, included with Kaeser Vacum Pump Assemblies, also may be ordered separately.