Vacuum Regulation Monitoring Vacuum Components For Sale In Kentucky

Part number "348-35" on schematic diagram.

Replacement foam filter sold separately. Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the M350 and M500 vacuum controller is a combination noise suppressor and air filter providing a large washable...

The Model 350 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 350 CFM ASME and features direct sensing that is sensitive to 0.1" hg of change in vacuum pressure.

Model 100 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 150 CFM ASME and features direct sensing that is sensitive to 0.1" hg of change in vacuum pressure.

The Model 500 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 500 CFM ASME and features direct sensing that is sensitive to 0.1" hg of change in vacuum pressure.

4” x 4” x 2” unit prints characters and graphics on a strip of paper. Includes cables, paper roll, and AC transformer.

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

Replacement Foam Filter for 173-02010 Vacuum Regulator. Two filters required.

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

Part number "353-06" on schematic diagram.

Straight Brass Stall Cock; 3/8" thread.

Angle Brass Stall Cock; 3/8" thread.

Factory calibrated for accuracy. Glycerine fill assures accuracy by providing a cushion against vibration. Dual scale, Hg and KPA. Vacuum gauges assure accurate readings of line vacuum and provide constant monitoring for maximum herd protection.

Fits assemblies with 20 to 25 HP pump. Straight Silencer with 4" NPT. Extra quiet, glass-packed silencers, included with Kaeser Vacum Pump Assemblies, also may be ordered separately.

Fits assemblies with 50 to 60 HP pump. Straight Silencer with 8" NPT. Extra quiet, glass-packed silencers, included with Kaeser Vacum Pump Assemblies, also may be ordered separately.

Worn Parts Replacement Kit for MK11 Mark II Vacuum Controller. Kit contains: O-Ring, Top dome filter, Adjusting knob, Dome diaphragm, Diaphragm assembly, Flange screws (3), Flange assembly, Outlet seal, Rolling seal and Air Filter.

Factory calibrated for accuracy. Glycerine fill assures accuracy by providing a cushion against vibration. Dual scale, Hg and KPA. Vacuum gauges assure accurate readings of line vacuum and provide constant monitoring for maximum herd protection.

Replacement foam filter sold separately. Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the model M100 vacuum controller is a combination noise suppressor and air filter providing a large washable...

Nickel-Plated brass stall cocks have a large diameter passage, positive on/off and NPT thread. Fine quality--economically priced

Large Carrying Case can hold the Digimet Unit, the printer, battery pack, cables, instruction manual and accessories.

Stall Cock Repair Kit includes 2 long screw, 1 o-ring, 1 short screw, 2 insulating washer, 6 brass washers, 2 stall cock inserts, and 1 ball.

Leeson Washguard motors are designed and built for extended life in the wet, humid environment of the dairy. 2HP with a 7/8" shaft in a stainless steel finish, three phase, 145TC frame, 208-230/460 voltage, and 3600 RPM.

Operating on the servo principle (where a separate sensor, the servo pilot valve, senses the line vacuum, compares it to a pre-set value, then signals the main control valve to adjust airflow to maintain the pre-set value), this system is very accurate,...

Repair Kit for Fullwood/BouMatic (blue) Vacuum Regulator contains gaskets, O-rings and filters.

Other fine features include... Please call to take advantage of our Computer-Assisted Pump Sizing Program, which considers all the variables and recommends the right size pump for the job.

Replacement End Cap for 15" tank with three 3" inlets.

Replacement Drain - 1 1/4"