Vacuum Components Milking Equipment For Sale In Idaho

The Peacekeeper for the Mark II vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the noise created by air flow into the controller.

With dusty conditions there is only one way to guarantee that pulsators get the clean air that enables them to function at peak efficiency. Use with a standard automotive-type filter.

Worn Parts Replacement Kit for MK11 Mark II Vacuum Controller. Kit contains: O-Ring, Top dome filter, Adjusting knob, Dome diaphragm, Diaphragm assembly, Flange screws (3), Flange assembly, Outlet seal, Rolling seal and Air Filter.

Servo-style Vacuum Regulator is ideal for pipelines or portable milking operations. Regulator has two washable replaceable filters. Accurate, quiet and easy to install, this Regulator reads vacuum levels up to 3000 LPM (105 CFM) .

Our low-cost, quick-mount Fresh Air Filter is attached directly to 3” PVC pipe and can handle six pulsators. Features green plastic body with replaceable foam filter.

Stabilvac Safety Valve is designed to work exclusively with the Stabilvac to provide safe milking vacuum. In the unlikely event of regulator malfunction, the safety valve assures a safe vacuum level.

For use with Strangko, Bou-Matic, Schlueter and Westfalia electric pulsators. Threaded Style screws directly into the tubing so no clamp is required. Die-cast, rust-free metal construction.

Overall dimensions 7" in diameter and 12.5" high. May be adjusted between 10" and 15". 3" Female NPT mounting connections. The Model 500 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 500 CFM ASME and features...

4” x 4” x 2” unit prints characters and graphics on a strip of paper. Includes cables, paper roll, and AC transformer.

Replacement Drain 1-1/2".

Replacement End Cap for 15" tank with 1-1/2" drain opening.

The design allows for quick installation, and the unit can be cleaned and serviced in less than 10 minutes. The Monobloc Stabilvac Regulator will maintain consistent vacuum between 34 kPa (10” Hg) and 60 kPa (18” Hg) at airflow up to 6,300 l/min (223...

Double-wall corrugated box with expanded polystyrene corner pads. A plug is included to seal off the unneeded outlet in single configuration. Pre-Air Filters are packaged in 350-lb.

Kaeser Pump Oil is a special synthetic oil especially recommended for Kaeser pumps. It requires changing much less often than ordinary petroleum-based oils.

There is about 4 CFM needed per cow. Pump performance, or CFM, varies according to ambient temperature, humidity, air pressure, elevation and many other factors. At sea level at a temperature of 68F, with a 2HP motor, the RPM of this model is 1250 and...

Replacement Stainless Steel screen for old-style Pre-Air Filters. Dimensions 10-7/8"W by 18"L by 5/16".

There is about 4 CFM needed per cow. Pump performance, or CFM, varies according to ambient temperature, humidity, air pressure, elevation and many other factors. At sea level at a temperature of 68F, with a 1.5HP motor, the RPM of this model is 1400 and...

Double-wall corrugated box with expanded polystyrene corner pads. A plug is included to seal off the unneeded outlet in single configuration. Pre-Air Filters are packaged in 350-lb.

Straight Brass Stall Cock; 3/8" thread.

Repair Kit for Fullwood/BouMatic (blue) Vacuum Regulator contains gaskets, O-rings and filters.

The design allows for quick installation, and the unit can be cleaned and serviced in less than 10 minutes. The Separate Stabilvac Regulator will maintain consistent vacuum between 34 kPa (10” Hg) and 60 kPa (18” Hg) at airflow up to 6,300 l/min (223...

Replacement Lid Gasket for Pre-Filters 160201, 160206, 160208, 160237 and 160238

Relief Valve for Sentinel Controllers models M350 and M500 protects against occurrences of high vacuum. Part number "348-17" on schematic diagram. For systems with CFM's over 250, two are recommended.

Measuring only 32" long x 21" wide x 37" high and weighing 450 lbs., the 10HP Kaeser Compact is shipped fully assembled complete with Kaeser Tri-Lobe pump, stand, belt guard, silencer, drive package and remote oil drain.

Machined one-piece rotor assemblies High strength housing with cast iron endplates Heavy duty bearings & shafts Perfectly matched timing gears Reliable splash lubrication Dependable sealing Quality German design and manufacturing 24-Month Warranty against...

Plastic with nickeled brass insert, 3/8" thread.

Replacement End Cap for 15" tank with 1-1/4" drain opening.