Used Equipment Poultry Litter Equipment For Sale In Norwalk

42'' forks, fit over Tractor Loader Backhoe bucket with hooks, 45'' tall to center of round bar, round bar is 1-1/4''

ESCO, STANDARD DUTY BUCKET, 42'' , BUILT FOR KOMATSU PC220/210, 80 MM PINS OR 3.149'', 12-7/8'' ARM WIDTH, 18'' CENTER TO CENTER, SHANKS ARE AT TAIL END OF LIFE AND NEED BUILT UP, SHANKS ARE 6'' APART, OUTSIDE SHANKS ARE 5.5'' FROM INNER SHANKS, ESCO...

Werk-Brau,54''Case CX 350, Link Belt 350

HENDRIX 3/4 YARD DRAGLINE BUCKET

330LX, 10'-8'' ARM, AS IS WHERE IS.

WERK-BRAU HYDRAULIC COUPLER, COMES WITH MOST OF THE KIT-SOME MISCELLANEOUS FITTINGS COULD BE NEEDED ADDITIONALLY, UPPER IS MADE TO FIT JOHN DEERE 85-LOWER WAS MADE TO FIT JOHN DEERE 410.

GENESIS GMS700, RECONDITIONED AT GENESIS WINTER OF 2013, NON ROTATION, 2ND MEMBER, GOOD SHEAR , READY FOR WORK.

36'' CF BUCKET, 13-3/4'' BETWEEN EARS, 17.5'' CENTER TO CENTER, 80 MM PINS, NO TEETH, AS IS -WHERE IS.

SNELLER STUMP GRINDER, SELF CONTAINED, SETUP FOR EXCAVATOR MOUNT, YOU MUST RUN AUXILIARY FUEL LINE FROM ATTACHMENT TO CARRIER FUEL TANK, CUMMINS MOTOR, 190 HP, WAS MOUNTED ON A CASE 290.

48'' BUCKET, 13'' BETWEEN THE EARS THAT ARE CLOSEST TO TEETH BECAUSE BUSHING IS OUT- EARS SPACING ON THE BACK IS 12''-1/8'' , 17-1/4'' CENTER TO CENTER, 80 MM PINS, AS IS -WHERE IS

13' ARM, AS IS WHERE IS, NO CYLINDER, BOOM IN PICTURE IS ALSO AVAILABLE AT ADDITIONAL COST.

GEHL BACKHOE AND 2 BUCKETS,12'' AND 24'', ATTACHMENT IS SETUP FOR GEHL SKID STEER-YOU WILL NEED ADAPTER PLATE

BRADCO TRENCHER, 5' STINGER, COMES WITH ADDITION CHAIN IN PICTURES, HAS 3RD AUX. LINE FOR CASE OIL DRAIN, ATTACHMENT IS SETUP FOR GEHL SKID STEER- YOU WILL NEED UNIVERSAL ADAPTER PLATE OR NEED TO REMOVE GEHL MOUNT AND ADD UNIVERSAL FEMALE PLATE.

ESCO STD DUTY BUCKET MADE FOR LINK-BELT LS2800CII, 42''ONE SIDE IS PUSHED IN A LITTLE AND SO IS THE BOTTOM OF THE BUCKET, 70MM- 2.755'' PINS, CENTER TO CENTER IS 450MM- 17.72'', ARM WIDTH IS 320MM- 12.6''

10'6'' WIDE LIEBHERR BUCKET, 8.5 CUBIC YARD, FITS L564-462, L566-460, L574-472, L574-473, L576-457, L580-459, SLVZ, CENTER PIN MOUNT GAP IS 6'' WIDE AND WIDTH IS 11'', BOTH OUTSIDE LOWER PIN MOUNTS ARE 5.5'' WIDE, PIN DIAMETER IS 3- 3/16'', 34'' INSIDE...

1988 INTERSTATE TRAILER, MODEL 20DT, 24,330 GVWR, 25,450 GVWR WHEN OPERATING BELOW 54 MPH, 8' WIDE -19' LONG DECK, 5.5' BEAVERTAIL, 4'9''RAMPS, RAMPS ARE 21'' WIDE, 6 D-RINGS,TANDEM DUALS, 8.75''R16.5 WHEELS.

RECENT SERVICE GREAT RUBBER CLEAN MACHINE / CHEAP DELIVERY ANYWHERE

COOK BELLY DUMP, COMPLETELY GONE THROUGH IN 2010- HASN'T BEEN USED MUCH SINCE 2011, SOLID UNIT!

John Deere 8300 12 Foot Grain Drill, Double disc openers, Marker tires, rubber closing wheels, cover chains Disc Opener Type: Double, Drill Type: Pull, Field Ready

2011, CFI HYDRAULIC PROGRESSIVE LINK THUMB, FITS HYUNDAI 290LC-7A, 90 MM PINS, 15.75'' BETWEEN EARS.

BOOM FOR LINK-BELT 330LX, NO CYLINDERS, ARM IN PICTURE IS ALSO AVAILABLE AT ADDITIONAL COST.

La Bounty 2000R , have an estimate for shear jaw to be repaired from third party for $15,000, excavator 1997, Link-Belt 3400, 20,000 hours, comes with bucket and arm not pictured-with shear,bucket and arm- $70,000 for package, runs good.

YOU GET THE DRIVE UNIT ALL BITS AND EXTENSIONS PICTURED,LOWE 3300, ATTACHMENT IS SETUP FOR GEHL SKID STEER, 6''X8' AUGER , 2-4' EXTENSIONS, 15'' x4' AUGER , 2'' HEX STYLE,- YOU WILL NEED UNIVERSAL ADAPTER PLATE.

2005 CATERPILLAR 184-3397 / S325 ROTATING SHEAR, LOWER AND JAW PIN REBUILT, NEW BUSHINGS, NEW BEARINGS, NEW MAIN CYLINDER SHAFT 4 YEARS AGO OR 250 HOURS AGO,SETUP TO BE MOUNTED ON CAT 320.

HENSLEY ROCK BUCKET, V-BOTTOM, WITH PINS, FITS DEERE 410 AND 85,18''

HENDRIX 1 YARD BUCKET

2011 ALLIED AR 130 HAMMER, 3500 FT LB ENERGY, 350-470 BPM, 32-43 GPM REQUIRED, 3725 LB WEIGHT.