Used Equipment Heavy Equipment For Sale In Campbellton

Very sharp drill, Field ready Conventional drill , 22x8, press, double disc, Yetter hyd. 15' no-till or drill can be detached for use as a 3pt. Markers, great blades and coulters, only showing 6197 acres on counter.

30', sliding tounge, unit was a demo, like new

Gravity wagons, several in stock, Starting @ $1,250.

84" bucket, mounting brackets, quick attach hyd valve, no joystick, no welds, fits JD 7000 series Bucket Size: 84, Model Fits: 7000 series

5 bottom in furrow

Can convert back to sprocket drive if needed Deck Plates: Manual, Field Ready, Snout Type: Metal, Telescoping Drive 6R36, dry drive, CM shafts, straight tin, We leased this head out in fall of 2017 to cut 300 acres with no problems.

Good 15' flex head, 3" cut, poly tines, dividers, (3) Available.

Field ready Front Disk Blade Size: 23, Rear Disk Blade Size: 24, Walking Tandems Has a couple of welds. 29'3", rock flex, rear hitch and hydraulics for crumbler, hydraulic fore/aft, walking tandems, 23" front and 24" rear blades.

All bought new at same time w/ consecutive serial numbers, slip tounges, all metal, no wood, great rubber, light kits. Or 8,500 for pair. Good clean wagons with very little use.

Wings taken off for transport Deck Plates: Manual, Outer Side Shield, Snout Type: Metal Clean hard-to find head. Will fit K or K2 machine.

Good clean 20' drill set up for soybeans, 20x15, planter units, V-press, hydraulic markers, spray bar, 3 pt.

21x7, double disc, 3" press, cylinder Disc Opener Type: Double, Drill Type: Pull, End Wheels, Field Ready, Number of Openers: 21

21x7, double disc, double run, good blades Disc Opener Type: Double, Drill Type: Pull, Field Ready, Number of Openers: 21

6RW, hyd fold, hyd pump,

500 gallon, 45' booms, 3 way nozzles, foamers, walking tandems, pto pump, manual lift, no controls Foam

18' flex, 3" cut, Stainless floor, Sprocket drive, Poly, Good auger and floor, Dividers taken off for transport

Wings off for transport Deck Plates: Manual, Outer Side Shield, Snout Type: Metal Off K2 combine. 2R30, very clean hard-to-find head.

Good 15' flex head, 3" cut, metal tines, (3) Available.

Very sharp head for year. Good auger and floor. 20' flex, 3" cut, sprocket drive. Dividers taken off for transport. Cart not included

Head only, no cart Deck Plates: Manual, Field Ready, Snout Type: Metal, Stalk Stompers: 2 4R36, high tin, dry drive, dual sprocket drive, stalk chompers, sprockets and chain are fair/good.

Cab, Air, Heat, Radio, Forward Speed: 8, Front Tire % Remaining: 30, Front Tire Size: 28.1-26, Front Tire Type: Singles, Front Weights: yes, Fuel Type: Diesel, PTO: 1000, PTO Size: 1 3/8, Rear Tire % Remaining: 30, Rear Tire Size: 28.1-26, Rear Tire Type:...

Has stalk chomper, Field ready 4R36, Great chains, sprockets, rollers, knives, floor and tin.

Head only, no cart! Deck Plates: Manual, Telescoping Drive Dual jackshafts, Good rollers, chains, sprockets and knives. Straight head w/ good tin. Head has been test run and sounds good.

Always barn kept. Original paint w/ no polish needed. Standard rotor, beater, cummins engine, reverser, GLM, new a/c compressor w/ cold air, 1-owner, This is the one of the cleanest machine's we have had in a long time.

45' booms, 3 way nozzles, foamers, controls, pto pump, hydraulic lift, single axle, mix tank Foam

Fore/aft, single drive, dividers, (3) Available. 20' flex head w/ 3" cut, tear drop reel, hyd.

3" cut, pipe reel, double drive, grain grabbers, dividers, good floor and auger, head only, no cart