Used Equipment Gleaner For Sale In North Salt Lake

0% for 2 years!! 1130 eng hrs, 873 sep hrs, 18.4x42 inners, 14.9x46 outer duals setup for 6R30, 18.4x26 rears, smarttrac lateral tilt, finecut chopper, chaff spreader, 390bu powerfold bin ext, powerfold ladders, HD variable speed header drive, deluxe...

0% for 2 years!! 924 eng hrs, 577 sep hrs, 18.4x42 straddle duals, 18.4x26 rears, smarttrac lateral tilt, finecut chopper, hyd straw spreader, HID Nighsight lights, deluxe leather seat, Fieldstar II yield monitor, powerfold ladders front & rear, 390 bushel...

0% for 5 years!! only 1051 eng, 696 sep hours, 18.4x42 duals, 16.9x26 rears, Maurer flare bin ext with tip ups, finecut chopper, variable speed header drive, EZ close rock door, CDF rotor with spacer bars, Hyd straw spreader, Fieldstar II field monitor,...

0% for 2 years!! 708 eng hrs, 404 sep hrs, 18.4x42 duals, 18.4x26 rears, HD variable speed, HID lights, Finecut II 24 knife chopper, dual chaff spreader, hyd straw spreader, fieldstar II yield monitor, smart cooling engine fan, smattrac lateral tilt,...

0% for 2 years!! 924 eng hrs, 577 sep hrs, 18.4x42 straddle duals, 18.4x26 rears, smarttrac lateral tilt, fine cut chopper, hyd straw spreader, Nighsight HID lights, powerfold ladders frt & rear, deluxe leather seat, 390bu powerfold bin ext, long spout,...

0% for 2 years!! 708 eng hrs, 404 sep hrs, 18.4x42 duals, 18.4x26 rears, HD variable speed, HID lights, Finecut II 24 knife chopper, dual chaff spreader, hyd straw spreader, fieldstar II yield monitor, smart cooling engine fan, smattrac lateral tilt,...

2 heads 430& 315 Flex Transmission Type: 2 Spd

20ft flexhead for L or M series off of L3, quickcut sickle, poly skids, teardrop reel with poly teeth, teeth cut some but ok, stainless feathering sheets, long dividers, auger good, clean head, floor has 1 scrap and a couple lil pinholes that have been...

30ft with Crary Air Reel, SCH sickle, poly skids, long dividers, single point hookup, Gleaner R or S series smarttrac hookup, auger & floor good, reel good

25ft with Crary Air Reel, SCH sickle with rollers, poly skids, std dividers, power reel fore/aft, Gleaner nonsmarttrac hookup, auger & floor good,

SCH sickle with roller guides, HCC reel, long dividers, raised feather sheets, manual fore & aft, auger good, R series smarttrac hookup,

20ft series 2 floating cutterbar head, tigerjaw sickle, Weatherall single axle head trailer, Johnson rockguard, poly skids, std dividers with aftermarket extensions, wood bat reel with steel fingers & poly tile, floor good, auger has a few little dings,

20ft flexhead off Gleaner R50, SCH sickle with roller guides, poly skids, long dividers, tear drop reel with poly teeth, direct drive reel, reel teeth cut, couple dings in auger & floor,

Std 3" sickle, poly skids, HCC reel with poly teeth good, raised feather sheets, power fore & aft, standard dividers, 3 pos AHHC, auger & floor good,

20 foot, SCH sickle, HCC reel, poly skids, long dividers, power reel fore/aft, off R52, set up for nonsmarttrac hookup, can change to smarttrac hookup, potentiometer AHHC, no rock damage

30ft with Crary wind system, SCH sickle, poly skids, std dividers, Gleaner smarttrac hookup, power fore/aft, auger good, HCC reel, reel teeth good,

2012 GLEANER S77

Was - $89,900 - NOW - $74,900 R75 Gleaner Front Duals Variable Speed Header Drive Lateral Tilt Fieldstar GPS

2008 GLEANER R75 1414 SEPARATOR HOURS AGCO 350 HP HYDRO TRANSMISSION REAR WHEEL ASSIST 330 BU GRAIN TANK, LONG AUGER STRAW SPREADER CHOPPER 2-SPD SEPARATOR LARGE GRAIN CONCAVES ROCK TRAP AUTO HEADER HEIGHT AUTO GROUND SPEED VAR SPEED FEEDERHOUSE GRAIN...

Contact Bobby at 910-624-0566 for details!

4R36 cornhead for F, tin work good, chains & sprockets good, stripper plates good, snapping roller blades good, LH end snout slightly bent.

8R30 off L2, will fit M series too, chains & sprockets good, snapping roller blades square edge good, stripper plates good, ear savers, hoods & snouts good, parking stands, end dividers good

6R30 with electric adjustable stripper plates, Gleaner hookup, single point hookup, chains & sprockets good, snapping roller blades, stripper plates good, poly snouts, good shape

WAS $7,500 NOW $6,900