Used Equipment Digger Derrick Trucks For Sale In Kentucky

CONTINENTAL POST HOLE DIGGER - 12" AUGER. CALL LOUIE AT 530-569-0102 LOCATED IN CEDARVILLE, CA.

36" Long Auger, 9" Wide, 3Pt, 540PTO. Length:59" Width:59" Height:35"

Hydraulic drive for skid steer loader 9 inch auger x 36inches See all of our equipment on our website at www.jmseq.com and check us out on facebook too!

NEW Danuser EP15 post hole digger, skid steer QT mount, for hydraulic flow of 15-30 GPM, 12" x 48" fabricated auger

3 PT POST HOLE DIGGER, 540 PTO, HYDRALIC DOWN PRESSURE - VISIT OUR WEBSITE DEEREQUIPMENT.COM TO VIEW OUR INVENTORY ONLINE.

Rankin 18AR48 auger. Subject to stock on hand. MSRP: $495 + freight + setup.

SHAVER HD-8 POST DRIVER, 3 POINT ATTACHMENT

2018 Bobcat 15C

FRONTIER 3PT HITCH POST HOLE DIGGER WITH 12" BIT.

2018 Bobcat 15C

NEW Danuser EP10 post hole digger, skid steer QT mount, 12" x 48" auger, for hydraulic flow of 15-30 GPM

3 pt, 4" auger, 540 PTO, Stored Inside, 1 Owner, Mint Condition!!!

NEW Danuser T3 T-post driver, SS mounting plate, SS hoses & FF couplers, 2000 lbs impact force, 6 hits per second, drives T-posts & up to 3" pipe

Land Pride Post Hole Digger w/ 9" auger

2'' hex female to 2'' round male

Harleman 3305 Skid steer auger drive w/weight bars and boxes. $10,162.50 Harleman 36” Mult. Plane Rock Auger $4,000.00 Both together: $ 14,000.00 2 ½” Hex output shaft.

Truck has 175,000 miles and has a jerri-dan bed ,cat engine,6 speed trans,very good tires,new brakes,very clean inside and out.Has led flashing light on bed and diamond plated tool boxes on each side of frame.

Parting out dodge cummins ,good engine,tranny,body,fenders,ranch hand bumpers front and rear ,rims and tires Parting out dodge cummins ,good engine,tranny,body,fenders,ranch hand bumpers front and rear

Stock # 039., Located in Billings MT, Leica 2D Power Digger Excavator System, Includes 2D Panel, Power Snap Cradle, Boom, Stick and Bucket Sensors, Pitch and Roll Sensor, Direction Sensor, Found a lower price than ours?

Hercules 8' slip-in insulated box with a carrier transicold integra 30s refrigeration unit -20f to 86f 225 cubic feet Low hours used for a part time trucking route, sorry truck is not for sale.

The truck is a very nice and the only reason I am selling the truck is it is not needed any more. The truck is just to big for what I need it for. I have a 2000 model 18ft Mitsubishi box truck.

16ft bed, 375 hp 3406 Cat. 46000 rear end with 2 way lock (2 axles, 4 wheels) 3 way jake brake(2,4 & 6 cyl), air cond. 97200 actual miles. Engine has remaining factory warranty.

Plastic Lifter and Wrapper, For Produce, Crated, unassembled, Ask about $86 a month

Set up for intellislope

They all run and drive excellent. The two precision trucks are special edition beds with traction mat boxes. The ford has two spare tire holders inside the bed. L-10 cummins runs very well.

Ready to go to work. Price has been reduced to 20,000 for more detailed info. 1994 international toter truck , with 6 way hitch, 9 speed, percision built. Price has been reduced to 20,000

Came out of a working truck. 1975 International 2 speed Rear End. Will take no less than $300.00 for rear end. 1975 International 2 speed Rear End. Will take no less than $300.00