Used Equipment Asphalt Pavers Concrete Equipment For Sale In Norwalk

48'' Wer-Brau HD forks,8,000 lb capacity, upper pin spread 30-1/8''to 37-1/8'', bottom spread 37-1/8'' to 40-7/8'', 19.5'' center to center of lower and upper pin, were built for Ingersoll Rand IRWL350 compact wheel loader

42'' forks, fit over Tractor Loader Backhoe bucket with hooks, 45'' tall to center of round bar, round bar is 1-1/4''

ESCO, STANDARD DUTY BUCKET, 42'' , BUILT FOR KOMATSU PC220/210, 80 MM PINS OR 3.149'', 12-7/8'' ARM WIDTH, 18'' CENTER TO CENTER, SHANKS ARE AT TAIL END OF LIFE AND NEED BUILT UP, SHANKS ARE 6'' APART, OUTSIDE SHANKS ARE 5.5'' FROM INNER SHANKS, ESCO...

Werk-Brau,54''Case CX 350, Link Belt 350

HENDRIX 3/4 YARD DRAGLINE BUCKET

330LX, 10'-8'' ARM, AS IS WHERE IS.

WERK-BRAU HYDRAULIC COUPLER, COMES WITH MOST OF THE KIT-SOME MISCELLANEOUS FITTINGS COULD BE NEEDED ADDITIONALLY, UPPER IS MADE TO FIT JOHN DEERE 85-LOWER WAS MADE TO FIT JOHN DEERE 410.

GENESIS GMS700, RECONDITIONED AT GENESIS WINTER OF 2013, NON ROTATION, 2ND MEMBER, GOOD SHEAR , READY FOR WORK.

36'' CF BUCKET, 13-3/4'' BETWEEN EARS, 17.5'' CENTER TO CENTER, 80 MM PINS, NO TEETH, AS IS -WHERE IS.

SNELLER STUMP GRINDER, SELF CONTAINED, SETUP FOR EXCAVATOR MOUNT, YOU MUST RUN AUXILIARY FUEL LINE FROM ATTACHMENT TO CARRIER FUEL TANK, CUMMINS MOTOR, 190 HP, WAS MOUNTED ON A CASE 290.

48'' BUCKET, 13'' BETWEEN THE EARS THAT ARE CLOSEST TO TEETH BECAUSE BUSHING IS OUT- EARS SPACING ON THE BACK IS 12''-1/8'' , 17-1/4'' CENTER TO CENTER, 80 MM PINS, AS IS -WHERE IS

13' ARM, AS IS WHERE IS, NO CYLINDER, BOOM IN PICTURE IS ALSO AVAILABLE AT ADDITIONAL COST.

GEHL BACKHOE AND 2 BUCKETS,12'' AND 24'', ATTACHMENT IS SETUP FOR GEHL SKID STEER-YOU WILL NEED ADAPTER PLATE

LINE FOR CASE OIL DRAIN, ATTACHMENT IS SETUP FOR GEHL SKID STEER- YOU WILL NEED UNIVERSAL ADAPTER PLATE OR NEED TO REMOVE GEHL MOUNT AND ADD UNIVERSAL FEMALE PLATE. BRADCO TRENCHER, 5' STINGER, COMES WITH ADDITION CHAIN IN PICTURES, HAS 3RD AUX.

ESCO STD DUTY BUCKET MADE FOR LINK-BELT LS2800CII, 42''ONE SIDE IS PUSHED IN A LITTLE AND SO IS THE BOTTOM OF THE BUCKET, 70MM- 2.755'' PINS, CENTER TO CENTER IS 450MM- 17.72'', ARM WIDTH IS 320MM- 12.6''

10'6'' WIDE LIEBHERR BUCKET, 8.5 CUBIC YARD, FITS L564-462, L566-460, L574-472, L574-473, L576-457, L580-459, SLVZ, CENTER PIN MOUNT GAP IS 6'' WIDE AND WIDTH IS 11'', BOTH OUTSIDE LOWER PIN MOUNTS ARE 5.5'' WIDE, PIN DIAMETER IS 3- 3/16'', 34'' INSIDE...

1988 INTERSTATE TRAILER, MODEL 20DT, 24,330 GVWR, 25,450 GVWR WHEN OPERATING BELOW 54 MPH, 8' WIDE -19' LONG DECK, 5.5' BEAVERTAIL, 4'9''RAMPS, RAMPS ARE 21'' WIDE, 6 D-RINGS,TANDEM DUALS, 8.75''R16.5 WHEELS.

RECENT SERVICE GREAT RUBBER CLEAN MACHINE / CHEAP DELIVERY ANYWHERE

COOK BELLY DUMP, COMPLETELY GONE THROUGH IN 2010- HASN'T BEEN USED MUCH SINCE 2011, SOLID UNIT!

John Deere 8300 12 Foot Grain Drill, Double disc openers, Marker tires, rubber closing wheels, cover chains Disc Opener Type: Double, Drill Type: Pull, Field Ready

2011, CFI HYDRAULIC PROGRESSIVE LINK THUMB, FITS HYUNDAI 290LC-7A, 90 MM PINS, 15.75'' BETWEEN EARS.

BOOM FOR LINK-BELT 330LX, NO CYLINDERS, ARM IN PICTURE IS ALSO AVAILABLE AT ADDITIONAL COST.

La Bounty 2000R , have an estimate for shear jaw to be repaired from third party for $15,000, excavator 1997, Link-Belt 3400, 20,000 hours, comes with bucket and arm not pictured-with shear,bucket and arm- $70,000 for package, runs good.

YOU GET THE DRIVE UNIT ALL BITS AND EXTENSIONS PICTURED,LOWE 3300, ATTACHMENT IS SETUP FOR GEHL SKID STEER, 6''X8' AUGER , 2-4' EXTENSIONS, 15'' x4' AUGER , 2'' HEX STYLE,- YOU WILL NEED UNIVERSAL ADAPTER PLATE.

2005 CATERPILLAR 184-3397 / S325 ROTATING SHEAR, LOWER AND JAW PIN REBUILT, NEW BUSHINGS, NEW BEARINGS, NEW MAIN CYLINDER SHAFT 4 YEARS AGO OR 250 HOURS AGO,SETUP TO BE MOUNTED ON CAT 320.

HENSLEY ROCK BUCKET, V-BOTTOM, WITH PINS, FITS DEERE 410 AND 85,18''

HENDRIX 1 YARD BUCKET