Used Equipment Aggregate Equipment For Sale In Campbellton

Markers, great blades and coulters, only showing 6197 acres on counter. Very sharp drill, Field ready 15' no-till or drill can be detached for use as a 3pt. Conventional drill , 22x8, press, double disc, Yetter hyd.

30', sliding tounge, unit was a demo, like new

Gravity wagons, several in stock, Starting @ $1,250.

84" bucket, mounting brackets, quick attach hyd valve, no joystick, no welds, fits JD 7000 series Bucket Size: 84, Model Fits: 7000 series

5 bottom in furrow

6R36, dry drive, CM shafts, straight tin, We leased this head out in fall of 2017 to cut 300 acres with no problems. Can convert back to sprocket drive if needed Deck Plates: Manual, Field Ready, Snout Type: Metal, Telescoping Drive

Good 15' flex head, 3" cut, poly tines, dividers, (3) Available.

Has a couple of welds. Field ready Front Disk Blade Size: 23, Rear Disk Blade Size: 24, Walking Tandems 29'3", rock flex, rear hitch and hydraulics for crumbler, hydraulic fore/aft, walking tandems, 23" front and 24" rear blades.

All bought new at same time w/ consecutive serial numbers, slip tounges, all metal, no wood, great rubber, light kits. Or 8,500 for pair. Good clean wagons with very little use.

Will fit K or K2 machine. Wings taken off for transport Deck Plates: Manual, Outer Side Shield, Snout Type: Metal Clean hard-to find head.

Good clean 20' drill set up for soybeans, 20x15, planter units, V-press, hydraulic markers, spray bar, 3 pt.

21x7, double disc, 3" press, cylinder Disc Opener Type: Double, Drill Type: Pull, End Wheels, Field Ready, Number of Openers: 21

21x7, double disc, double run, good blades Disc Opener Type: Double, Drill Type: Pull, Field Ready, Number of Openers: 21

6RW, hyd fold, hyd pump,

500 gallon, 45' booms, 3 way nozzles, foamers, walking tandems, pto pump, manual lift, no controls Foam

18' flex, 3" cut, Stainless floor, Sprocket drive, Poly, Good auger and floor, Dividers taken off for transport

Off K2 combine. Wings off for transport Deck Plates: Manual, Outer Side Shield, Snout Type: Metal 2R30, very clean hard-to-find head.

Good 15' flex head, 3" cut, metal tines, (3) Available.

Good auger and floor. Dividers taken off for transport. 20' flex, 3" cut, sprocket drive. Cart not included Very sharp head for year.

4R36, high tin, dry drive, dual sprocket drive, stalk chompers, sprockets and chain are fair/good. Head only, no cart Deck Plates: Manual, Field Ready, Snout Type: Metal, Stalk Stompers: 2

We bought this tractor from Ohio 7 years ago and have been using on our farm to pull 12' offset and 12' box blade, we have put about 300 hrs on it. Cab, Air, Heat, Radio, Forward Speed: 8, Front Tire % Remaining: 30, Front Tire Size: 28.1-26, Front Tire...

4R36, Great chains, sprockets, rollers, knives, floor and tin. Has stalk chomper, Field ready

Head has been test run and sounds good. Head only, no cart! Deck Plates: Manual, Telescoping Drive Straight head w/ good tin. Dual jackshafts, Good rollers, chains, sprockets and knives.

Original paint w/ no polish needed. Standard rotor, beater, cummins engine, reverser, GLM, new a/c compressor w/ cold air, 1-owner, This is the one of the cleanest machine's we have had in a long time.

45' booms, 3 way nozzles, foamers, controls, pto pump, hydraulic lift, single axle, mix tank Foam

20' flex head w/ 3" cut, tear drop reel, hyd. Fore/aft, single drive, dividers, (3) Available.

3" cut, pipe reel, double drive, grain grabbers, dividers, good floor and auger, head only, no cart