Good condition Caterpillar engine. Blue 1996 GMC TRACTOR TOP-KICK LO-PRO. Excellent tire condition. Serious inquiries only. Stake truck in very good condition with electro-hydraulic tailgate for sale.
1993 Chevrolet Stake Body Truck with liftgate for sale. We have upgraded our fleet and no longer need this truck. 366 gas engine with 5 speed tranny and 2 speed rear end. Other than that, it's good to go.
This truck does have a rust spot on passenger door by mirror, missing tool box door on passenger side and will need tires. It is up to the individual to ask questions, inspect and satisfy his/her judgement before purchasing.
Low mileage of 46,552 original miles on the truck. This truck has the V-6 engine that GMC made for trucks, starting in 1960. NOTICE: This vehicle is offered AS-IS, WHERE-IS, with no warranty or guarantee, expressed or implied, as to its condition or fitness...
Current PA Inspections, Newer Tires. Please email for additional information or to set up appointment to see. Model C6500 stake body with dumping bed. Only 63,000 miles. 1997 Chevorlet Model C6500 stake body dumpster ,standard 6 speed transmittion.
The 4-Way Joint can also be used to cross-brace, preventing ‘push-out' caused by frost expansion. The 4-Way Joint (for 2" thick boards), allows connections in designs where four boards intersect.
✓ Can be used with 2 inch boards or standard 2” x 6” lumber
Our ingenious new Pivoting Connectors make it easy to create raised beds that will follow every twist and turn between 90 and 180 degrees. The hardest part of building raised beds is constructing corners that are square, strong and trim.
✓ Connectors pivot to angles between 90 and 180 degrees
✓ Hinged corners can form almost any angle greater than 90°
✓ Choice of four heights: 6", 8", 10" and 12", each sized to fit standard 2 x lumber
This truck has air brakes and reels for straps You won't be disappointed. It's has a 6cyl diesel engine and 5+5 gear transmission. Just passed inspection. Fully restored!! All new tires, brakes, paint, and exhaust.
Use these versatile corners to create everything from multi-level raised beds to angled landscape edging. Use with standard 2 x 6 lumber (fastening screws are included). Use singly for 5-1/2" high beds or edging, or stack two corners for an 11" high bed.
These simple 12" aluminum stakes fit into the channels of our Raised Bed Corners and In-Line Connectors, allowing you to stack 6" or 8" corners to create double-height and multi-tier raised beds easily.
The hardest part of building a raised bed is constructing corners that are square, strong and trim-looking. Our ingenious Gardener's Supply Raised Bed Corners are brackets that shorten building time and result in a handsome, sturdy raised bed every time.
✓ Set of 2 - buy two sets to build a complete bed
✓ Six heights, all designed to fit standard 2 x milled lumber (1 1/2" actual thickness)
✓ Powder-coated aluminum with plastic caps to keep out water
✓ Choose from 6 heights, each sized to fit standard 2 x 6, 2 x 8, 2 x 10 and 2 x 12 milled lumber
Each system also includes three regular Raised Bed Corners; just slide your own standard milled treated or untreated lumber into the corners and secure with the screws provided. You're ready to water — no more setting up sprinklers or standing around...
✓ Includes one Aquacorner, three regular Raised Bed Corners, 25' of soaker hose and fittings; you supply the lumber
✓ Soaker hose waters plants slowly and deeply, so minimal water is lost to runoff and evaporation
✓ Four heights: 6", 8", 10" and 12", designed to fit standard milled lumber
✓ Philips screws included
✓ Fittings are plastic
✓ Aquacorners are made of powder-coated aluminum with plastic cap, with brass fittings and attached spigot
For raised beds that won't bow out at the sides, use 4-foot planks and anchor them with our reinforcing In-Line Connectors, which come in sets of two. Made in Vermont by Gardener's Supply.
✓ Connectors reinforce the sides of raised beds to prevent bowing
✓ Set of 2
✓ Six heights, all designed to fit standard 2 x milled lumber
✓ Powder-coated aluminum with plastic caps to keep out water
According to customers requirements, we can design the opening type of truck doors,the temperature of truck body, the selection of inner devices,such as fixing device,suspension device,convection device,watering insulating and so on ,all what we can meet...
According to customers requirements, we can design the opening type of truck doors,the temperature of truck body, the selection of inner devices,such as fixing device,suspension device,convection device,watering insulating and so on ,all what we can meet...
Brass-Plated Steel Flagpole Holder is constructed from stamped heavy-gauge steel with a bright brass-plated finish and is designed to easily accommodate a pole with a 3/4 in.
Constructed from premium quality solid brass, this bracket is designed to withstand the test of time, so you can let your colors fly proudly. The idh by St. Simons 1 in. This premium quality bracket adds a sleek touch to your flag pole, without compromising...
✓ 100% solid brass ensures durability
✓ Can be mounted on vertical or horizontal surfaces
Constructed from hot forged brass, this bracket is designed to withstand the test of time, so you can let your colors fly proudly. The idh by St. Simons 3/4 in. This premium quality bracket adds a sleek touch to your flag pole, without compromising stability.
✓ Tools required: screwdriver and drill bit (recommended)
✓ Can be mounted on vertical or horizontal surfaces
✓ Coating prevents tarnishing or corrosion even in regular outdoor use
This adjustable flagpole bracket from Everreen is designed to fit many standard-sized poles. The bracket includes mounting hardware for an easy installation. This adjustable flagpole bracket is constructed of aluminum for weather resistance and long-lasting...
✓ Rust Resistant
✓ Adjustable
✓ Aluminum construction
Material: Aluminum
Outdoor Living Product Type: Flag/Flagpole Bracket
It is designed to accept 2 poles up to 1 in. This flag pole holder is constructed from dark brown plastic. It comes complete with fasteners for a quick and easy installation.
✓ Dark brown color
✓ Fasteners included for quick and easy installation
Adjustable: No
Outdoor Living Product Type: Flag/Flagpole Bracket
This holder features a 180 degree adjustable display angle and comes in a white powder coated finish. This flag pole holder is constructed from zinc diecast. It fits a 1/2 in.
✓ Rust Resistant
✓ Hardware Included
✓ Die-cast zinc construction
✓ Adjustable
Assembled Depth (in.): 2.875 in
Manufacturer Warranty: Goods are warranted against defects in manufacturing for 1 year. In no case is Prime-Line responsible for user related damage or damage incurred during installation. Warranty is void if products are subjected to abnormal conditions, misapplication or abuse.
