Replacement filters available. This regulator is recommended for vacuum pumps from 35 to 70 cfm (1,000 to 2,000 liters/min) and will maintain vacuum from 11” to 15” Hg (36 to 50 kPa).
In the unlikely event of regulator malfunction, the safety valve assures a safe vacuum level. Stabilvac Safety Valve is designed to work exclusively with the Stabilvac to provide safe milking vacuum.
Replacement filters available. This separate-style regulator, which divides the servo valve and the main control valve into two parts as shown, is recommended for vacuum pumps from 106 to 159 cfm (3,000 to 4,500 liters/min) and will maintain vacuum from...
Replacement foam filter sold separately. The Peacekeeper for the Mark II vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the noise created by air flow into the controller.
3" Female NPT mounting connections. May be adjusted between 10" and 15". The Model 350 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 350 CFM ASME and features direct sensing that is sensitive to 0.1" hg of change...
Replacement foam filter sold separately. The Peacekeeper for the model M100 vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the noise created by air flow into the controller.
Replacement filters available. This regulator is recommended for vacuum pumps from 12 to 35 cfm (350 to 1,000 liters/min) and will maintain vacuum from 10” to 15” Hg (36 to 50 kPa).
Replacement foam filter sold separately. The Peacekeeper for the M350 and M500 vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the noise created by air flow into the controller.
Regulator has two washable replaceable filters. Servo-style Vacuum Regulator is ideal for pipelines or portable milking operations. Accurate, quiet and easy to install, this Regulator reads vacuum levels up to 3000 LPM (105 CFM) .
2" Female NPT mounting connections. Featuring ABS housings and top dome and main filter, the Mark II may be adjusted between 10" and 15". The MKII Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 150 CFM ASME and...
Replacement filter feature a 200 micron mesh screen and is design for Item 41297. Replacing the filter on your drip irrigation system is highly recommended before each season. Irrigation filters can wear out and break down over the course of the season,...
3" Female NPT mounting connections. May be adjusted between 10" and 15". The Model 500 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 500 CFM ASME and features direct sensing that is sensitive to 0.1" hg of change...
FeaturingA a serial port and a variety of additional internal features, the Digimet 3000 displays average, maximum, and minimum vacuum level, fluctuation level, pulsator ratio, pulses per minute, milk/rest ratio.
Replacement filters available. This separate-style regulator, which divides the servo valve and the main control valve into two parts as shown, is recommended for vacuum pumps from 35 to 106 cfm (1,000 to 3,000 liters/min) and will maintain vacuum from...
Part number "348-17" on schematic diagram. Relief Valve for Sentinel Controllers models M350 and M500 protects against occurrences of high vacuum. For systems with CFM's over 250, two are recommended.
Main line systems by using a ¾ in. Filter can be used with 1 in., ¾ in., and ½ in. Filter housing comes with filter. Having a filter on your drip irrigation system is highly recommended as filters keep larger particles from passing into your drip tape...
Use to replace a damaged or worn unit or to create your own drip irrigation system with our other irrigation components. Use to monitor water pressure in your irrigation system. Too high or low pressure can be an early warning that something needs to...
Make sure you are keeping proper pressure in your drip system so you don't blow out your drip lines. Use to replace a damaged or worn unit or to create your own drip irrigation system with our other irrigation components.
