Milk Line Washing Components Milking Equipment For Sale In San Diego

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Use the Coburn stainless steel claw hanger whenever you need to hang a Delaval or other style claw upside-down. Ideal for storage and cleaning in place, this claw hanger includes hangar and U-bolt for installation on stall tubing.

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Short round wash and milk shut-off plug for 2" line.

Coburn"s Black Plastic Distributor Tee is smooth throughout for efficient water flow and is an economical alternative to the Stainless Steel Distributor Tee.

Long round wash and milk shut-off plug for 2" line.

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Three-Jar Dispenser may be combined with the Timer Control Module to make a complete pipeline wash system. Of water hose, and sink bracket. Three-Jar Dispenser includes hot and cold water valves, 25 ft.

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

1.5" Blue Plastic Milk Valve features a 5/8" inlet.

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Concentric Reducing Ferrule reduces from 2" to 1-1/2" tube and is 1-1/8" long.

Butt-Weld-end Special Y for 2" tube OD features "A" dimension of 3-1/2" and "B" dimension of 7". Type 304 Stainless Steel.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Reducer from 3" OD to 2.5" OD tube is 2" long.

180 Degree clamp-end U-bend for 2" tube OD features "A" dimension of 6". Type 304 Stainless Steel.

This CIP Assembly for DeLaval and IBA features Stainless Steel jetter rack and 120115 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

Butt weld end tee for 2-1/2" tube has L-dimension of 3" and B-dimension of 6".

90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 2" OD tube features inner radius of 3" and center distance (C) of 3.5".

Solid End Cap for Bevel Seat is made of Type 304 Stainless Steel with #4 Dairy Finish. End cap for 3" OD tube has 3.44" OD.

Of chemical tubing. The timer is easily programmed to deliver the precise amount of cleaner required for the pump, which in most cases is a very small amount. The Cleaning System includes peristaltic pump with control, straight injector and 10 ft.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Reducer from 3" OD to 2" OD tube is 4" long.

Thermometer registers from 1 to 220F and the face is 1" diameter with a 5" stainless steel stem. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

180 Degree butt-weld U-bend for 2.5" tube OD features "A" dimension of 7-1/2". Type 304 Stainless Steel.

Teflon bevel seat gasket for 2.5" OD tubing.

180 Degree clamp-end U-bend for 3" tube OD features "A" dimension of 9". Type 304 Stainless Steel.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Reducer from 4" OD to 2" OD tube is 8" long.

2.5" Blue Plastic Milk Valve features a 5/8" inlet.