Milk Line Washing Components Milking Equipment For Sale In Michigan

Summit E Programmer is used to control the #1209838 Three-Pump Peristaltic Pump to automate and improve accuracy of dairy sanitation chemical dispensing. Programmer can set a variety of adjustments including on/off, run times and delay times from 1 second...

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120116 Jetter Cups for Surge. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

Thermometer registers from 1 to 220F and the face is 1" diameter with a 5" stainless steel stem. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7102.

Long round wash and milk shut-off plug for 2" line.

Replacement pump tube with fittings, 8" piece."

RFE Silicone Grease f / Peristaltic Pump Tubing. Silicone Grease (Required when replacing Peristaltic Pump Tubes)

This CIP Assembly for BouMatic features Stainless Steel jetter rack and 120117 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120117 Jetter Cups for Boumatic. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

L5000 Plus Panel features stainless steel cabinet with new sloping design, snap-in pump heads, internal trigger module, and 20 oz/600ml per minute capacity. 115 volt 60 HZ. L5000 Plus Peristaltic 3-Pump Panel can be retrofitted to existing pipeline wash...

Glass-to-Stainless Steel Ferrule with Gasket Groove is made of Type 304 Stainless Steel with #4 Dairy Finish. 3/4" long for 1.5" OD tube.

This smooth, white Tee is made out of food-grade plastic.

Screw for Blue Milk Valve.

Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish. 1-1/8" long for 3" OD Tube.

Black Gasket, (top under slide) 9/16".

90 Degree tube bend for 2" tube OD features "A" dimension of 4-1/16". Type 304 Stainless Steel.

Clamp end tee for 1-1/2" tube has A-dimension of 2-3/4" and B-dimension of 5-1/2".

90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 1" OD tube features inner radius of 1.5" and center distance (C) of 2".

Clamp-end Special Y for 3" tube OD features "A" dimension of 5" and "B" dimension of 10". Type 304 Stainless Steel.

Bevel-seat recessless ferrule for 2-1/2" tubing is 1-1/2" long.

Clamp end tee for 1-1/2" tube has A-dimension of 2.375" and B-dimension of 4.75".

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Reducer from 4" OD to 1.5" OD tube is 10" long.

Bevel-seat recessless ferrule for 3" tubing is 1-7/16" long.

2" Blue Plastic Milk Valve features a 5/8" inlet.

90 Degree Sweep Ell is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on one end and butt weld on the other. Ell for 2.5" OD tube features "A" dimension of 5-3/16" and "B" dimension of 5-11/16”.

Stainless Steel Slide for Blue Milk Valve.

Teflon Tri-Clamp Gasket.