Milk Line Washing Components Milking Equipment For Sale In District Of Columbia

It may be combined with the 8950 Timer Control Module for more functionality. Three-Pump Dispenser features three motor-driven peristaltic pumps each with 300 oz. Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer...

CIP components are sold individually, or as part of complete kit. Stainless Steel Fit ‘em All Heavy Duty Jetter Rack will hold virtually any milking claw including Delaval. Hardware is included.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7102.

Coburn"s S.S. Distributor Tee with vent hole is smooth and clean throughout for efficient water flow. Tubes are aligned for ease and convenience of hose handling.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120117 Jetter Cups for Boumatic. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

3" Wash Valve weighs 3 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Thermometer has a recalibration feature and includes a plastic carrying case. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

Timer Control Module features electro-mechanical timing, failsafe timer, standard 8-minute wash cycle, 24-hour clock for automatic pre-sanitizing, door interlock and is CSA-approved.

Long round wash and milk shut-off plug for 3a" line.

This smooth, white Tee is made out of food-grade plastic.

The 120112 has rounded insert for holding the jetter cups. Jetter Rack is sold individually, or as part of complete kit. Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval.

This CIP Assembly for BouMatic features Stainless Steel jetter rack and 120117 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish. 1-1/8" long for 1" OD Tube.

Short round wash and milk shut-off plug for 2-1/2" line.

Stainless Steel Nut for Blue Milk Valve.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7100.

External Seal Kit for LC Thomsen #4, 5 or 6 Milk Pumps includes housing gasket, rotary seal assembly, ceramic seal and 2 impeller clips. After-market equipment.

Teflon Tri-Clamp Gasket.

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features a standard clamp on one end and butt weld on the other. Ferrule for 2.5" OD tube is 1/2" long with 2.370" ID.

Concentric Reducing Ferrule reduces from 2" to 1-1/2" tube and is 1-1/8" long.

Bevel-seat recessless ferrule for 2" tubing is 1-3/8" long.

Solid End Cap for Tri-Clover line is made of Type 304 Stainless Steel with #4 Dairy Finish. End cap for 4" OD tube has 4.68" OD.

Clamp end tee for 3" tube has A-dimension of 3-3/4" and B-dimension of 7-1/2".

Teflon bevel seat gasket for 3" OD tubing.

Bevel-seat recessless ferrule for 3" tubing is 1-7/16" long.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and featuresstandard clamp fitting on both ends. Reducer from 4" OD to 3" OD tube is 5-1/8" long.

Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish. 1-1/8" long for 2" OD Tube.