Milk Line Washing Components Milking Equipment For Sale In Colorado

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts. This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120117 Jetter Cups for Boumatic.

Replaces Milk-Rite 7103. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation. This CIP Assembly for DeLaval and IBA features Stainless Steel jetter rack and 120115 jetter cups.

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately). May be plumbed directly to the drain. 50-60 Hz, .31 amp. 115VAC with drip-proof motor enclosure.

Thermometer has a recalibration feature and includes a plastic carrying case. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

110V Motor f/Depend-O-Drain

2-1/2" Wash Valve weighs 2.5 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Ideal for storage and cleaning in place, this claw hanger includes hangar and U-bolt for installation on stall tubing. Use the Coburn stainless steel claw hanger whenever you need to hang a Delaval or other style claw upside-down.

It may be combined with the 8950 Timer Control Module for more functionality. Three-Pump Dispenser features three motor-driven peristaltic pumps each with 300 oz. Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer...

Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval. The 120112 has rounded insert for holding the jetter cups. Jetter Rack is sold individually, or as part of complete kit.

Replaces Milk-Rite 7100. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Coburn"s Black Plastic Distributor Tee is smooth throughout for efficient water flow and is an economical alternative to the Stainless Steel Distributor Tee.

1-1/8" long for 2.5" OD Tube. Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish.

Spring Retainer Washer

Clamp end tee for 4" tube has A-dimension of 4-1/2" and B-dimension of 9".

Butt weld bevel-seat ferrule for 4" tubing.

Bevel-seat recessless ferrule for 3" tubing is 1-5/8" long.

Includes 3 shaft O-rings, 1 head O-ring, 1 rotary seal spring, 1 teflon rotary seal and 2 impeller clips. Internal Seal Kit for LC Thomsen Milk Pump.

3" Blue Plastic Milk Valve features a 5/8" inlet.

2.5" Blue Plastic Milk Valve features a 5/8" inlet.

Type 304 Stainless Steel. 90 Degree tube bend for 2.5" tube OD features "A" dimension of 5-3/16".

Butt weld end tee for 1-1/2" tube has L-dimension of 2-1/4" and B-dimension of 4-1/2".

This smooth, white Tee is made out of food-grade plastic.

White Gasket, 5/8" for Blue Milk Valves.

Butt weld bevel-seat ferrule for 3" tubing is 29/32" long and B-dimension of 3-7/16" and C-dimension of 2-55/64".

End cap for 4" OD tube has 4.68" OD. Solid End Cap for Tri-Clover line is made of Type 304 Stainless Steel with #4 Dairy Finish.