Milk Line Washing Components Milking Equipment For Sale In California

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts. This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120115 Jetter Cups for DeLaval and IBA.

Tubes are aligned for ease and convenience of hose handling. Coburn"s S.S. Distributor Tee is smooth and clean throughout for efficient water flow.

Long round wash and milk shut-off plug for 3a" line.

Bender Diverter Valve - 120V

LEDs are added to help diagnose washer trigger supply issues. L5000 Plus Panel features stainless steel cabinet with new sloping design, snap-in pump heads, internal trigger module, and 20 oz/600ml per minute capacity.

1-1/8" long for 2.5" OD Tube. Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish.

Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Stainless Steel Nut for Blue Milk Valve.

1.125" long for 1" OD Tube. Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish.

Of chemical tubing. The Coburn Lobe Pump Wash System helps prevent the build-up of milkfat and other residues on the lobes of the vacuum pump and protects the pump from rust and corrosion.

Butt weld bevel-seat ferrule for 2" tubing is 23/32" long and B-dimension of 2-3/8" and C-dimension of 1-55/64".

1-3/8" long for 2.5" OD tube. Plain Recessless Ferrule for standard clamp is made of Type 304 Stainless Steel with #4 Dairy Finish.

Reducer from 4" OD to 2" OD tube is 8" long. Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends.

Long round wash and milk shut-off plug for 2" line.

Long round wash and milk shut-off plug for 2" line.

Ell for 3" OD tube features "A" dimension of 6-5/16" and "B" dimension of 6-13/16”. 90 Degree Sweep Ell is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on one end and butt weld on the other.

1-1/8" long for 4" OD Tube. Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish.

Teflon bevel seat gasket for 2" OD tubing.

Type 304 Stainless Steel. 180 Degree clamp-end U-bend for 2" tube OD features "A" dimension of 6".

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts. This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120117 Jetter Cups for Boumatic.

Teflon Tri-Clamp Gasket.

Thermometer registers from 1 to 220F and the face is 1" diameter with a 5" stainless steel stem. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

Ferrule for 1.5" OD tube is 1/2" long with 1.375" ID. Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features a standard clamp on one end and butt weld on the other.

Stainless Steel Milk Valve for 1.5" - 3" lines features a 5/8" inlet.

3" Clamp X 3" NPT. Horizontal Moisture Trap comes complete with cover, gasket, clip and ball.

End cap for 2.5" OD tube has 2.91" OD. Solid End Cap for Bevel Seat is made of Type 304 Stainless Steel with #4 Dairy Finish.

1-1/8" long for 3" OD Tube. Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish.