Milk Line Washing Components Farm Supplies For Sale In Seattle

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120115 Jetter Cups for DeLaval and IBA. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

Wall or direct-mounted, air injector operates on 120 volts. Intake orifice is 1-1/2". Improved Sentinel Air Injector activates at a minimum of 5" of vacuum, has a capacity of 200 cubic feet of air per minute on 15" of vacuum, and can be easily adjusted.

Of water hose, and sink bracket. Jars have a capacity of 30 oz. Three-Jar Dispenser may be combined with the Timer Control Module to make a complete pipeline wash system. Three-Jar Dispenser includes hot and cold water valves, 25 ft.

This CIP Assembly for BouMatic features Stainless Steel jetter rack and 120117 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

The 120112 has rounded insert for holding the jetter cups. Hardware is included. Jetter Rack is sold individually, or as part of complete kit. Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7100.

Silicone Grease (Required when replacing Peristaltic Pump Tubes) RFE Silicone Grease f / Peristaltic Pump Tubing.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7102.

Thermometer has a recalibration feature and includes a plastic carrying case. Thermometer registers from 1 to 220F and the face is 1" diameter with a 5" stainless steel stem. CIP Thermometer is used to make sure the CIP wash solution is at the required...

110V Motor f/Depend-O-Drain

Bender Diverter Valve - 240V

Short round wash and milk shut-off plug for 2-1/2" line.

2-1/2" Wash Valve weighs 2.5 lbs. Shut-off plugs and parts available separately. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which...

1-1/2" long for 4" OD tube. 1-1/8" long for 1.5" OD tube. 1-3/8" long for 2.5" OD tube. Plain Recessless Ferrule for standard clamp is made of Type 304 Stainless Steel with #4 Dairy Finish.

Plain Recessless Ferrule for standard clamp is made of Type 304 Stainless Steel with #4 Dairy Finish. 1-3/8" long for 2.5" OD tube.

Internal Seal Kit for LC Thomsen Milk Pump. Includes 3 shaft O-rings, 1 head O-ring, 1 rotary seal spring, 1 teflon rotary seal and 2 impeller clips.

Short Weld Ferrule is made of Type 304 Stainless Steel with #4 Dairy Finish and features threading on one end and butt weld on the other. Ferrule for 3" OD tube is 29/32" long.

Butt-Weld-end Special Y for 1.5" tube OD features "A" dimension of 2-3/4" and "B" dimension of 5-1/2". Type 304 Stainless Steel.

5/8" Stainless Steel Gooseneck fits 150200A Sliding Milk Valve.

Butt weld end tee for 1-1/2" tube has L-dimension of 2-1/4" and B-dimension of 4-1/2".

Black Gasket, (top under slide) 5/8".

90 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 2" OD tube features inner radius of 3" and center distance (C) of 3.5".

Rubber tri-clamp gasket for 1" OD tubing.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and featuresstandard clamp fitting on both ends. Reducer from 4" OD to 2" OD tube is 9-1/8" long.

90 Degree tube bend for 4" tube OD features "A" dimension of 8-5/16". Type 304 Stainless Steel.

90 Degree Sweep Ell is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on one end and butt weld on the other. Ell for 2" OD tube features "A" dimension of 4-1/16" and "B" dimension of 4-9/16”.

180 Degree butt-weld U-bend for 1.5" tube OD features "A" dimension of 4-1/2". Type 304 Stainless Steel.