Milk Line Washing Components Farm Supplies For Sale In Michigan

L5000 Plus Panel features stainless steel cabinet with new sloping design, snap-in pump heads, internal trigger module, and 20 oz/600ml per minute capacity. 115 volt 60 HZ. LEDs are added to help diagnose washer trigger supply issues.

Tubes are aligned for ease and convenience of hose handling. Coburn"s S.S. Distributor Tee with vent hole is smooth and clean throughout for efficient water flow.

2-1/2" Wash Valve weighs 2.5 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

3" Wash Valve weighs 3 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Jetter Rack is sold individually, or as part of complete kit. The 120112 has rounded insert for holding the jetter cups. Hardware is included. Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval.

Replaces Milk-Rite 7103. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Coburn Vacuum Pump Cleaner contains a rust inhibitor to protect the pump from rust and corrosion. Five-gallon pail.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation. This CIP Assembly for Surge features Stainless Steel jetter rack and 120116 jetter cups.

Coburn"s Black Plastic Distributor Tee is smooth throughout for efficient water flow and is an economical alternative to the Stainless Steel Distributor Tee.

Bender Diverter Valve - 240V

4" Wash Valve weighs 5 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Kit contains: O-Ring, Top dome filter, Adjusting knob, Dome diaphragm, Diaphragm assembly, Flange screws (3), Flange assembly, Outlet seal, Rolling seal and Air Filter. Worn Parts Replacement Kit for MK11 Mark II Vacuum Controller.

Long round wash and milk shut-off plug for 2" line.

Replaces Milk-Rite 7101. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Silicone Grease (Required when replacing Peristaltic Pump Tubes) RFE Silicone Grease f / Peristaltic Pump Tubing.

2" Blue Plastic Milk Valve features a 5/8" inlet.

Type 304 Stainless Steel. 90 Degree tube bend for 3" tube OD features "A" dimension of 6-5/16".

Ell for 3" OD tube features "A" dimension of 6-5/16" and "B" dimension of 6-13/16”. 90 Degree Sweep Ell is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on one end and butt weld on the other.

2" rubber gasket for Surge stainless steel pipeline.

End cap for 3" OD tube has 3.58" OD. Solid End Cap for Tri-Clover line is made of Type 304 Stainless Steel with #4 Dairy Finish.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts. This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120115 Jetter Cups for DeLaval and IBA.

Clamp end tee for 1-1/2" tube has A-dimension of 2-3/4" and B-dimension of 5-1/2".

1-1/8" long for 2" OD Tube. Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish.

Reducer from 1.5" OD to 1". Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and featuresstandard clamp fitting on both ends.

Not recommended for applications where pressure exceeds 150 psi. This high-quality butterfly valve for 4" tube is made of type 316 Stainless Steel for clamp connection.

Extra heavy cross clamp fits two pieces of 2-3/8" tubing.

Stainless Steel Pipeline Hanger comes with rubber grommets to hold pipe securely in place.