Milk Line Washing Components Farm Supplies For Sale In Connecticut

Thermometer has a recalibration feature and includes a plastic carrying case. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts. This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120116 Jetter Cups for Surge.

Long round wash and milk shut-off plug for 2" line.

It may be combined with the 8950 Timer Control Module for more functionality. Three-Pump Dispenser features three motor-driven peristaltic pumps each with 300 oz. Capacity, switch setting to program pump run time, hot and cold water valves, cycle timer...

Short round wash and milk shut-off plug for 2" line.

Replaces Milk-Rite 7100. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Replaces Milk-Rite 7101. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Jetter Rack is sold individually, or as part of complete kit. Hardware is included. Stainless Steel Fit ‘em All Jetter Rack will hold virtually any milking claw including Delaval.

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

CIP components are sold individually, or as part of complete kit. Stainless Steel Fit ‘em All Heavy Duty Jetter Rack will hold virtually any milking claw including Delaval. Hardware is included.

Programmer can set a variety of adjustments including on/off, run times and delay times from 1 second to 45 minutes. Summit E Programmer is used to control the #1209838 Three-Pump Peristaltic Pump to automate and improve accuracy of dairy sanitation chemical...

Bender Diverter Valve - 120V

2" Wash Valve weighs 2 lbs. High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts. This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120115 Jetter Cups for DeLaval and IBA.

Concentric Reducing Ferrule reduces from 2" to 1-1/2" tube and is 1-1/8" long.

Includes Gaskets and Seal to repair old-style Delaval Milk Pump.

Reducer from 4" OD to 1.5" OD tube is 10" long. Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends.

Elbow for 2.5" OD tube features "C" dimension of 2-1/16". 45 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends.

1-3/8" long for 2.5" OD tube. Plain Recessless Ferrule for standard clamp is made of Type 304 Stainless Steel with #4 Dairy Finish.

Not recommended for applications where pressure exceeds 150 psi. This high-quality butterfly valve for 2.5" tube is made of 304 Stainless Steel for clamp connection.

Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation. This CIP Assembly for DeLaval and IBA features Stainless Steel jetter rack and 120115 jetter cups.

Reducer from 4" OD to 2" OD tube is 9-1/8" long. Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and featuresstandard clamp fitting on both ends.

Clamp end tee for 4" tube has A-dimension of 4-1/2" and B-dimension of 9".

Original equipment kit. External Seal Kit for LC Thomsen Model #4 Milk Pump includes head O-ring, 2 impeller clips, ceramic seal and rotary seal assembly.

Type 304 Stainless Steel. Clamp-end Special Y for 1.5" tube OD features "A" dimension of 2-3/4" and "B" dimension of 5-1/2".

2.5" Blue Plastic Milk Valve features a 5/8" inlet.

1.5" Blue Plastic Milk Valve features a 5/8" inlet.