Milk Line Washing Components Farm Supplies For Sale In Columbus

115VAC with drip-proof motor enclosure. Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately). May be plumbed directly to the drain.

This CIP Assembly features Fit-'em-All Stainless Steel Jetter Rack and 120117 Jetter Cups for Boumatic. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, Stainless Steel Distributor, U-Bolts and Nuts.

RFE Silicone Grease f / Peristaltic Pump Tubing. Silicone Grease (Required when replacing Peristaltic Pump Tubes)

Diverter Plug for 2" Glass Tee.

Coburn"s S.S. Distributor Tee is smooth and clean throughout for efficient water flow. Tubes are aligned for ease and convenience of hose handling.

Long round wash and milk shut-off plug for 3a" line.

Thermometer registers from 1 to 220F and the face is 1" diameter with a 5" stainless steel stem. CIP Thermometer is used to make sure the CIP wash solution is at the required 160F degrees at the start of the wash cycle.

Butt weld end tee for 2-1/2" tube has L-dimension of 3" and B-dimension of 6".

Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish. 1-1/8" long for 2" OD Tube.

Butt weld end tee for 3" tube has L-dimension of 3-1/4" and B-dimension of 6-1/2".

Concentric Reducing Ferrule reduces from 3" to 2" tube and is 1-5/16" long.

Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head. Replaces Milk-Rite 7102.

Spring Retainer Washer

Ceramic wear ring with Viton boot.

This CIP Assembly for BouMatic features Stainless Steel jetter rack and 120117 jetter cups. Like our other CIP Kits, it also includes Smooth Approved Barbless Tee, Duckbill Drain, U-Bolts and Nuts for installation.

Long Weld Ferrule is made of type 304 Stainless Steel with #4 Dairy Finish. 1-1/8" long for 1" OD Tube.

Replacement pump tube with fittings, 8" piece."

Butt-Weld-end Special Y for 1.5" tube OD features "A" dimension of 2-3/4" and "B" dimension of 5-1/2". Type 304 Stainless Steel.

115 volt 60 HZ. L5000 Plus Panel features stainless steel cabinet with new sloping design, snap-in pump heads, internal trigger module, and 20 oz/600ml per minute capacity. LEDs are added to help diagnose washer trigger supply issues.

90 Degree Sweep Ell is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on one end and butt weld on the other. Ell for 2.5" OD tube features "A" dimension of 5-3/16" and "B" dimension of 5-11/16”.

Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and features butt weld fitting on both ends. Reducer from 2" OD to 1.5" OD tube is 2" long.

Stainless Steel Pipeline Hanger comes with rubber grommets to hold pipe securely in place.

90 Degree tube bend for 2.5" tube OD features "A" dimension of 5-3/16". Type 304 Stainless Steel.

Bevel-seat recessless ferrule for 4" tubing is 1-1/2" long.

Butt weld bevel-seat ferrule for 1-1/2" tubing is 23/32" long and B-dimension of 1-27/32" and C-dimension of 1-23/64".

45 Degree Elbow is made of Type 304 Stainless Steel with #4 Dairy Finish and features standard clamp fitting on both ends. Elbow for 2.5" OD tube features "C" dimension of 2-1/16".

Clamp end tee for 1-1/2" tube has A-dimension of 2-3/4" and B-dimension of 5-1/2".