Milk Line Washing Components Farm Supplies For Sale In Colorado

Programmer can set a variety of adjustments including on/off, run times and delay times from 1 second to 45 minutes. Summit E Programmer is used to control the #1209838 Three-Pump Peristaltic Pump to automate and improve accuracy of dairy sanitation chemical...

Tubes are aligned for ease and convenience of hose handling. Coburn"s S.S. Distributor Tee with vent hole is smooth and clean throughout for efficient water flow.

Replaces Milk-Rite 7100. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Black rubber Duck Bill-style Drain Valve is used with CIP assemblies and moisture traps.

115 volt 60 HZ. L5000 Plus Panel features stainless steel cabinet with new sloping design, snap-in pump heads, internal trigger module, and 20 oz/600ml per minute capacity. L5000 Plus Peristaltic 3-Pump Panel can be retrofitted to existing pipeline wash...

Diverter Plug for 2" Glass Tee.

Bender Diverter Valve - 240V

High-quality stainless steel wash valves include two high-density polyethylene paddles, one short paddle which allows milk to flow into receiver, and one long paddle which blocks wash water.

Drain valve assembly mounts directly to the wash vat drain fittings with a no-hub coupling (available separately). 50-60 Hz, .31 amp. May be plumbed directly to the drain. 115VAC with drip-proof motor enclosure.

Replacement pump tube with fittings, 8" piece."

Long round wash and milk shut-off plug for 2" line.

110V Motor f/Depend-O-Drain

Replaces Milk-Rite 7102. Smooth, sanitary, rubber Jetter Cups are tapered for better cleaning of the inflation head.

Fits all claws including DeLaval. Heavy duty Drawer-Style Stainless Steel Jetter Rack includes nuts and bolts for mounting.

Bevel-seat recessless ferrule for 2-1/2" tubing is 1-1/2" long.

2" Blue Plastic Milk Valve features a 5/8" inlet.

1-3/8" long for 2.5" OD tube. Plain Recessless Ferrule for standard clamp is made of Type 304 Stainless Steel with #4 Dairy Finish.

Type 304 Stainless Steel. 180 Degree clamp-end U-bend for 2" tube OD features "A" dimension of 6".

A complete pipeline washer may be made by combining the Timer Control Module with the 9740 Three-Jar or the 9590 Three Pump Dispenser. Timer Control Module features electro-mechanical timing, failsafe timer, standard 8-minute wash cycle, 24-hour clock...

Kit contains: O-Ring, Top dome filter, Adjusting knob, Dome diaphragm, Diaphragm assembly, Flange screws (3), Flange assembly, Outlet seal, Rolling seal and Air Filter. Worn Parts Replacement Kit for MK11 Mark II Vacuum Controller.

Short round wash and milk shut-off plug for 2" line.

Butt weld bevel-seat ferrule for 2-1/2" tubing is 27/32" long and B-dimension of 2-29/32" and C-dimension of 2-23/64".

Reducer from 4" OD to 2.5" OD tube is 7-1/8" long. Concentric Reducer is made of Type 304 Stainless Steel with #4 Dairy Finish and featuresstandard clamp fitting on both ends.

Type 304 Stainless Steel. 90 Degree tube bend for 3" tube OD features "A" dimension of 6-5/16".

Stainless Steel Nut for Blue Milk Valve.

Seal Kit f/Old-Style Surge Milk Pump - Includes carbon seal, rubber seal, small e-clip, try clamp flapper, surge style flapper, large 4" head gasket, 1/12" gasket.

Type 304 Stainless Steel. Clamp-end Special Y for 1.5" tube OD features "A" dimension of 2-3/4" and "B" dimension of 5-1/2".