Livestock Waterers Farm Supplies For Sale In Washington

The upper arm is orange and is located in the top bracket of the top base and is held by a lock pin. It moves the plunger to and from the orfice.

SPI 3.75" Brass Short Float Stem only.

Robert's Brass 1/2" sand plunger only for replacement in existing 1/2" valve. Suggested where sugar sand is a problem in the water supply.

Blue plastic valve assembly fits a 3/4" FPT with a .25" orfice inlet. Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm.

This model features an adjustable short arm for customizing water level. The R400 series is a high-capacity float valve with male NPT inlet and outlet connections. Robert's Brass 3/8" orifice Valve complete with plunger and arms.

SUPERB ENERGY EFFICIENCY FOR NEW INSTALLATIONS YOU ONLY NEED ONE UNIT FOR UP TO 150 HEAD Please see our brochure WP012 Brochure

Used to insulate the Heat Well below the frost line, preventing the loss of energy into the frozen ground. Won't rust, resists rot & hold up to chemically active soil conditions. Corrugated design provides rigidity without bulk when back filled with earth.

Apex replacement float with string included.

3 year warranty. The larger tanks come with 1.25� drains installed. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction tanks.

This quick release "D" clip is used on all of the New Generation Energy Free Waterers (4 per Unit) & on the Electric Waterer's inspection plates.

Control Diaphragm w/ ABS Stem & Strainer

Its diaphragm principle of operation allows the Topaz to give flows of up to 90 gallons per minute. Features Has Detach for quick access to valve seal Mounts horizontally or vertically Made from corrosion resistant materials Shuts down slowly to minimize...

Used to extend the Insulated Earth Tube into warm ground below the frost line & form the Heat Well. Won't rust, resists rot & holds up to chemically active soil conditions. Corrugated design provides rigidity without bulk when back filled with earth.

Pride of the Farm Plastic Nut Only that holds the base & plunger tight inside the Valve Body. #10 on breakdown.

The valve has a 1” water level differential between opening and closing, reducing pump motor overload. Fully submerged valve is almost indestructible to livestock and models come in standard tail length and long tail length.

3-year warranty. This smaller sized water tank for the corner of your tack room takes up less space. 10 1/2" side panels x 11 1/4" front panel x 71" tall. No stand available for this water caddy.

VP2 Valve Upgrade Kit for 1/8" Orifice Valve

45 Gallon, 48" x 35" x 25" - 1345# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Filter replacement for Topaz & Megaflow Valves.

Black rubber seat to fit inside the Mira Fount RED Plunger in a Mira Fount cattle waterer valve.

Two Year Warranty High Volume - 2400 GPH at 40 PSI Animal Damage-Resistant Design No Float Ball or Moving Parts Unaffected by Freezing Hudson Valve with European Thread for 1-140 PSI with 1/2" female thread is 5" high and 3.75" in diameter.

The peaked roof and raised ribs around the door openings prevent manure, feed and other contaminants from being washed into the bowl, and facilitates water run off. Earth Tube is suggested with installation.

The larger tanks feature incorporated pallet fork opening on the bottom, eliminating accidental punctures while providing easy transportation. High Country Plastics Water tanks are rotational molded with high quality FDA approved UV protected plastic...

Was exactly what I needed. After 3 weeks of use, we have no leaks or overflows. The dogs chew on everything so I used the metal housing. Arrived within three days. I was purchasing to replace an older one that finally wore out.

Robert's 3/4" leather cup ring that fits on the brass plunger.

Robert's shut off only arm attached to the bottom of the Robert's Brass Valve.