Livestock Waterers Farm Supplies For Sale In Utah

6, 7 and 12 (see parts list in pictures attached) B81 includes: Ref. B81 Hook, Rod, Cone and Nut Assembly for WFD85 and MFD85 field drinker.

The valve has a 1” water level differential between opening and closing, reducing pump motor overload. Working pressure range is 4-175 psi, working water temperature range 34-140 F.

3/4" male to female hose used to hook up the water line to the waterer.

The D-Clip features no tools required to remove lid, no crossed/stripped thread failures, quick replacement if damaged & commonly available at farm supply stores. The low profile design & fully hinged door provids animals better access to the capacity...

Repair kit includes 1 each screen, retainer ring, diaphragm, shut-off pad and float.

Unlike common ball float valves, the Hudson Valve does not constrict the flow prior to positive shut-off. Valve body parts are made out of a durable glass-filled nylon, which is vented to eliminate siphoning.

White polyethylene disc float only.

Plastic piece that sits on top of the float. It is held by a float screw and connects on to the bottom of the float arm.

SPI Rubber door hinges with screws for all of the New Generation energy free waterer. (sold in pairs)

The valve has a 1” water level differential between opening and closing, reducing pump motor overload. Working pressure range is 4-175 psi, working water temperature range 34-140 F.

This bolt package is for Models 101, 202 & 404 with or without heat.

Arkfeld waterer element replacement. 600 watt x 120 volt heating element only

Stock Tank With Built-In Drinker Model PRE224BID comes standard with one built-in drinker. -Minimal Assembly -Strong Utra-violet Light Protection to prevent Fading/Cracking -One Inch (2.54 cm) Drain Plug (Drain is to the left as you face drinker) -Drinker...

Robert's 1/2" Leather cup ring that fits on the brass plunger.

Dependable, non siphoning valve - proven & trouble free. Unique baffles guard against icing & keep valve operating under severest conditions. Seamless sidewall cannot leak. No pulleys & cable to foul & rust.

Unlike common ball float valves, the Hudson Valve does not constrict the flow prior to positive shut-off. Valve body parts are made out of a durable glass-filled nylon, which is vented to eliminate siphoning.

It not only ends flooding, breakdown and water loss, it also does away with breakage of floats, balls, and lever arms by livestock. Mounting bracket sold separately. The positive shut-off feature functions in an 8 psi to 140 psi water pressure range.

Features Has Detach for quick access to valve seal Mounts horizontally or vertically Made from corrosion resistant materials Shuts down slowly to minimize water hammer 3/4″-2 1/2″ water level differential (increases as water inlet pressure increases)...

Continuous flow disc and repair kit for use with Hudson valves.

2" built in drain, stainless steel spring loaded attachment pins make cover removal & replacement easy, recessed, protected notches for secure anchoring, overflow port & dependable non-siphoning Durapride Valve.

Dimensions: 39" x 37" x 23" This Jug 4 Hole Waterer has a 45 gallon tank capacity & waterers 125 head of Dairy, 250 head of Beef & 300 head of Sheep. It's maximum 24-hr electical use is 1.56 kwh.

Both the water line & the electrical supply can enter from below. The heat tube is designed to mate with the cavity under the drinker base. You should use silicon caulk to assure an airtight fit.

SPI white corrugated baffle for model 4x4 energy free waterer.

A brass rod float arm 1/4" x 1" with threads on each end. Connects valve to round float.

The valve has a 1” water level differential between opening and closing, reducing pump motor overload. Working pressure range is 4-175 psi, working water temperature range 34-140 F.

Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float. Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm.