Livestock Waterers Farm Supplies For Sale In Toledo

SPI foamed 4x4 energy free waterer door only.

Click HERE for instructions & Repair Parts Heater included: 250 watts, 110 volts. Our VT100 valve delivers about 2 1/2 gallons (9.5 liters) per minute. We tested this unit in a cold chamber at minus 30 degrees Fahrenheit (-34.4 degrees C).

Very efficient use of energy. 5 year warranty. 22" W x 27" L x 26" H 7 gal. Engineered with the farmer in mind, this waterer allows easy access to submersible heater, water line, incoming services and provides effortless cleaning; an extremely low maintenance...

The lower arm is orange and is located in the bottom bracket of the top base and is held by a lock pin. It moves the upper to and is also held by a thumbscrew to the float arm.

This Dare farm tank float valve with aluminum housing has a 300 gallon per hour capacity and a tough blow-molded plastic float. We stock all replacement parts. Connects to 3/4 garden hose or adaptable for pipe.

The peaked roof and raised ribs around the door openings prevent manure, feed and other contaminants from being washed into the bowl, and facilitates water run off. The low profile design and fully hinged door provides animals better access to the water.

Grade A compliant. Pride of the Farm's trough drinker is a favorite for feedyards , pastures and dairies. It is loaded with features not available on any competing trough drinker. Extra supply line protection, patented water circulation, multiple constant...

20 Gallon, 36" x 35" x 25" - 1060# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

#1 on breakdown. No other parts are included with this Power Link. Pride of the Farm Power Link locks to the VP124 valve body with a link pin & then thumbscrews to the float arm.

Inside repair kit for Topaz & Megaflow Valve.

Screw that holds the float connect to the top of the float.

A round float for Arkfeld,SPI or Mira Fount waterers.

87" L x 62" W x 20" H 91# 5 Year warranty High Country Plastics water tanks are rotational molded with high quality FDA approved UV protected plastic to ensure uniform thickness & strength for maximum durability & longevity.

Arkfeld waterer element & thermostat replacement. 600 watt x 120 volt heating element with surface mount thermostat included.

Unaffected by ground movement due to freezing & thawing. Corrugated design provides rigidity without bulk when back filled with earth. Won't rust, resists rot & holds up to chemically active soil conditions.

Stock Tank With Built-In Drinker Model PRE224BID comes standard with one built-in drinker. -Minimal Assembly -Strong Utra-violet Light Protection to prevent Fading/Cracking -One Inch (2.54 cm) Drain Plug (Drain is to the left as you face drinker) -Drinker...

A brass rod float arm 1/4" x 8" with threads on each end. Connects valve to 301 round float.

Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet. Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm.

1 year warranty. The 250W elemnt is encased in aluminum for durability & safety. Farm Innovator's Ice Chaser operates automatically only during freezing temperatures. SAFE IN PLASTIC.

* The Ice Sweeper comes with a full 3-year limited replacment warranty, exclusive only of exposed seals. Compared to other "intermittent flow devices", the Ice Sweeper is very dependable, uses less water & shuts off water flow reliably when the threat...

Manufacturer recommends that you secure tank with ratchet tie-downs (not provided) to prevent movement from side-to-side while traveling. 3 year warranty. Comes with an 8' heavy duty hose with ball valve to fill from the bottom, 2 mounting straps to secure...

The tank also comes with a 1.25" drains installed. Aqua Blue color only. Dimension: 50" x 33 1/4" x 24 1/4" If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill...

Upright Water Caddy Stand (24694) will work with this water caddy. This tank fits conveniently into the "dead space" in the corner of the walk-in tack room. White 14 1/2" x 14 1/2" x 56" tall.

Often used in Franklin & Arkfeld waterers. Turns on at 36 degrees and turns off at 48 degrees. Surface mount thermostat used in galvanized waterers.

Heating element ONLY for all Johnson Concrete Models EXCEPT the J360.

#12-3 on the breakdown. This part number is for the arm only & is usually used on the Polar Max waterers. Pride of the Farm Plastic 3 5/8" Float arm is connected to the Power Link by a thumbscrew & then screws directly into the Poly float.

Plastic piece that sits on top of the float. It is held by a float screw and connects on to the bottom of the float arm.