Livestock Waterers Farm Supplies For Sale In Tacoma

Typical heating cost for one heating season only $10! 250 Watt, 110 volt heater.

It moves the plunger to and from the orfice. The upper arm is orange and is located in the top bracket of the top base and is held by a lock pin.

45 Gallon, 48" x 35" x 25" - 1345# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Connects valve to 301 round float. A brass rod float arm 1/4" x 5" with threads on each end.

These are not included when ordering a base only. There are four base screws that hold the top base to the bottom base.

Filter replacement for Topaz & Megaflow Valves.

It has O'ring on one side & a Diaphragm on the other (not included). #7 on breakdown. Pride of the Farm 1/4" Orifice on a VP124 Valve.

The Jug Basic Float Valve fits Models J101, 202, 303 & 404 with or without heat.

We are all delighted to have the replacement installed - easy to do - and the waterer functioning perfectly. Our original float valve got broken during the barn remodel.

Includes seat and float. Repair Kit for Water Control Valves model 825H , 825P , 830H , 830P , 825ASH and 825ASP .

25-gallon FDA approved plastic has a valve located at the bottom of the tank which allows you to water your horses in transit, or at your destination with water from home. This tank fits conveniently into the "dead space" in the corner of the walk-in...

1 1/4" pipe plug that will accept a heater or float valve system. Tank dimensions: 51 1/2" long, 29" wide, 24" high.

This repair kit will fit in all Apex Valves & is made for use in all high pressure or low pressure applications.

A drain plug for the Arkfeld waterers - 1 1/2" in size - Black rubber.

B79P Plastic Float with Arm for WFD85 and MFD85 field drinkers. B79P includes:Ref. 14, 15, 16 in parts list.

PVC pipe from valve to hose threads. Contains J-bolt brackets which mount to tank edge.

Robert's Brass 3/4" plunger only for replacement in existing 3/4" valve.

Same desription as the J202 EXCEPT THIS UNIT HAS NO HEAT!

Blue Flap for WPM20 Cattle Waterer

Thermostaically controlled to only run when necessary. The 1500 Watt element easily converts from a safe plastic floating de-icer into a submergible de-icer with a simple removal of the float.

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

They mount above or below the water and give flows of up to 6 gallons per minute. FEATURES: Side, Bottom, Top Mounting Valve body screws apart by hand for easy servicing Flow stops when unscrewed for servicing Supplied with back-nut and seal washer Built...

One-piece body polyethylene construction has smooth rounded edges for safety and can stand up to livestock abuse. Holds 6 gallons. Approximately 48 lbs. Has 2” to 3” urethane foam insulation.

SPI foamed 4x4 energy free waterer door only.

The floats seal the water away from outside. Capacity: 150 hd beef 60 hd dairy, 2-9 1/4" ball closure. Tested in continental U.S. to remain frost-free with as few as 6 head drinking every other day.

Molded with the most effective ultraviolet inhibitor. Drinker wells are 14" deep allowing most any animal to drink naturally. You don't need extra heat to keep the line above the ground open.