Livestock Waterers Farm Supplies For Sale In Pasadena

3/4" orfice only for the inside of a Franklin Valve.

The upper arm is orange and is located in the top bracket of the top base and is held by a lock pin. It moves the plunger to and from the orfice.

Fully submerged valve is almost indestructible to livestock and models come in standard tail length and long tail length. The top entry model provides an air gap, preventing back-flow.

There are four base screws that hold the top base to the bottom base. These are not included when ordering a base only.

Hollow black plug used in all Franklin galvanized waterers.

Arkfeld waterer element replacement. 600 watt x 120 volt heating element only

Robert's 1/2" Leather cup ring that fits on the brass plunger.

The larger tanks come with 1.25� drains installed. Available in Aqua Blue color only. 28 1/2" x 20" x 10 1/4" 3 year warranty. If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common...

Float Arm for the Mira Fount M3330 waterer.

This repair kit fits the Models 101, 202 & 404 with or without heat.

Arkfeld waterer element replacement. 1000 watt x 120 volt heating element only.

Megaflow Float Valves are ideal for filling troughs which are constructed to have the valve mounted under the water on the side or on the bottom. Its diaphragm principle of operation allows the Megaflow to give flows of up to 90 gallons per minute.

You can mount this valve on the bottom or on the side and has a bouyancy equal to a 6" round float. It has an above water float adjustment, cord cleat for shutting off valve and a 1 1/2" water level differential from open to close.

Black rubber seat to fit inside the Mira Fount Blue Plunger in a Mira Fount cattle waterer valve.

A greater flow rate because the plunger travels a longer distance; 3. VP2 VALVE The VP2 is our next generation valve which replaces our VP1 valve series. Greater tolerance to operation in dirty conditions; 4.

Megaflow Yellow Float Only.

Fits most flat walls of trailers and comes with a shut-off valve and two tie straps. Constructed of an FDA-approved plastic. The upright water tank has a cap at the top for easy filling.

Use this valve assembly with the J303 with without heat.

This exchange of water keeps the water warm even in the coldest climate. The floats seal the water away from outside. University testing showed that the fountain worked when temperatures were at -100 degrees wind chill and never required any external...

The tank also comes with a 1.25" drains installed. 3 year warranty. Dimension: 50" x 33 1/4" x 24 1/4" Aqua Blue color only. If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane...

Pride of the Farm Cam Link locks to the VP124 valve body on the top side with a link pin. This is the arm that opens & closes the plunger. No other parts come with the Cam Link. #2 on breakdown.

Robert's Brass 1/2" sand plunger only for replacement in existing 1/2" valve. Suggested where sugar sand is a problem in the water supply.

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

I found the stated 50 gallon water capacity ends up being 35 gallons. It's designed to be positioned at the back or front of a fender well with convenient and easy access to water fill caps located on both sides.

45 Gallon, 48" x 35" x 25" - 1345# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

A round float for Arkfeld,SPI or Mira Fount waterers.

Blue octagon plunger that fits inside the Mira Fount cattle waterer valve.