Livestock Waterers Farm Supplies For Sale In Newfoundland And Labrador

It has an excellent insulating property of R15 and amazing structural strength. The dimensions of this tube is 12 3/4" OD x 49" tall with 2 1/2" of insulation. The SPI Insulated Earth Tube conserves the earth ground source heat as it rises up the vertical...

Connects to 3/4" garden hose or adaptable for pipe. We stock all replacement parts. This Dare anti-siphon farm tank float valve with weather-resistant plastic housing has a 300 gallon per hour capacity and a tough blow-molded plastic float.

SPI 351/352 New Generation Gasket.

This is the arm that opens & closes the plunger. #2 on breakdown. No other parts come with the Cam Link. Pride of the Farm Cam Link locks to the VP124 valve body on the top side with a link pin.

The Tru-Test Apex Xtraflo 3/4" valve with brass rod arm attached to the black round float for Anti-Siphon use.

If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole. Available in Forest Green in stock, other colors such as Ash Grey, Black, Blue, Red & Tan available...

Robert's Brass 1/2" orfice Valve complete with sand plunger and arms.

The upper arm is orange and is located in the top bracket of the top base and is held by a lock pin. It moves the plunger to and from the orfice.

Robert's 1/2" rubber plunger seat only.

250 Watt, 110 volt heater. Typical heating cost for one heating season only $10!

SPI 351/352 (old style) Rubber Drain Plug only .

Plastic piece that sits on top of the float. It is held by a float screw and connects on to the bottom of the float arm.

Surface mount thermostat used in galvanized waterers. Turns on at 36 degrees and turns off at 48 degrees. Often used in Franklin & Arkfeld waterers.

20 Gallon, 36" x 35" x 25" - 1060# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Robert's Brass 1/2" sand plunger only for replacement in existing 1/2" valve. Suggested where sugar sand is a problem in the water supply.

A brass rod float arm 1/4" x 10" with threads on each end. Connects valve to 301 round float.

Robert's 3/4" rubber cup ring that fits on the brass plunger.

Meets "Grade A" Dairy requirements (non-siphoning). Very efficient use of energy. The polyethylene used in our SPI Livestock Waterers is FDA and HPB approved, food grade, recyclable plastic.

The valve has a 1” water level differential between opening and closing, reducing pump motor overload. Working pressure range is 4-175 psi, working water temperature range 34-140 F.

The MicroSweeper requires no maintenance, no electricity and no adjustment, EVER. The intermittent flow MicroSweeper can be easily plumbed in any type of waterer, no matter how it was originally equipped.

Heating element ONLY for all Johnson Concrete Models EXCEPT the J360.

Used to insulate the Heat Well below the frost line, preventing the loss of energy into the frozen ground. It will take abuse! Unaffected by ground movement due to freezing & thawing.

Protect your underground water line from freezing. 14" x 30" long, 2" thick. Can be used with Mirafount or other brand installations.

Megaflow Yellow Float Only.

Robert's 1/2" Leather cup ring that fits on the brass plunger.

Each valve comes with installation instructions, warranty information and parts list. Rubber shut-off pad and ABS plastic and stainless steel internal parts ensure long life. Fluid level forces the float to rise and close the diaphragm chamber, which...

The valve has a 1” water level differential between opening and closing, reducing pump motor overload. Working pressure range is 4-175 psi, working water temperature range 34-140 F.