Livestock Waterers Farm Supplies For Sale In Irvine

The orange cap only that fits over the insides of the Franklin Valve.

SPI 2 1/2" Brass Short Float Stem only.

It has O'ring on one side & a Diaphragm on the other (not included). #7 on breakdown. Pride of the Farm 1/4" Orifice on a VP124 Valve.

Robert's Brass 3/4" plunger only for replacement in existing 3/4" valve.

Float Arm for the Mira Fount M3330 waterer.

Corrugated design provides rigidity without bulk when back filled with earth. Used to insulate the Heat Well below the frost line, preventing the loss of energy into the frozen ground.

Valve works with up to 70 lbs. The Trough-O-Matic float valve features a longer, deeper float which gives more leverage. The rust-proof plastic cover is fitted with a 3/4" female hose connection.

Fluid level forces the float to rise and close the diaphragm chamber, which expands to stop incoming flow. Unlike common ball float valves, the Hudson Valve does not constrict the flow prior to positive shut-off.

Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm. Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float.

Corrugated design provides rigidity without bulk when back filled with earth. Used to extend the Insulated Earth Tube into warm ground below the frost line & form the Heat Well. 15" OD, corrugated plastic tubing.

Connects valve to 301 round float. A brass rod float arm 1/4" x 10" with threads on each end.

Robert's Brass thumbscrew that connects the short arm and long arm.

Turns on at 35 degrees & turns off at 45 degrees. Operates with any 15 amp 120V electric heater or fan. Five controlled temperatures (one just right for you) & no installation required.

Black rubber seat to fit inside the Mira Fount RED Plunger in a Mira Fount cattle waterer valve.

It's maximum 24-hr electical use is 1.56 kwh. Features: *Open bowl design *Draw Tube for natural drinking action *External Drain Plug for easy cleaning *Sledge hammer tough, rotationally molded plastic construction *Inspection cover for easy access to...

Optional ground mount tube (Model HT10) for hookup to underground service connections and for outdoor installations. Our chamber can go as low as minus 30 degrees F (-34.4 degrees C).

Replacement drain plug for MiraFount Waterers.

XtraFlo is UV stabilized and corrosion resistant. The valve has a 1” water level differential between opening and closing, reducing pump motor overload. XtraFlo compact diaphragm valve has full-flow, high volume fill.

Our R-valve of 7.5 per inch holds the heat provided by incoming water. Incoming water carries heat energy. Two 2 inch side drains and 1 threaded bottom port for optional inside drain.

This orange plunger holds the seat (not included) and is pushed by the upper arm towards or away from the orfice.

The High Country Plastics TC-63 Pickup Bed Water Caddy is an innovative way to haul up to 63 gallons of fresh water in your pickup truck while still allowing for easy hook-up to a gooseneck trailer.

SPI 4x4 Rubber Drain Plug only.

Maximum 24-hr electrical use on the Jug 101 is 1.56kwh. Features: *Open bowl design *Draw Tube for natural drinking action *External Drain Plug for easy cleaning *Sledge hammer tough, rotationally molded plastic construction *Inspection cover for easy...

Use this valve assembly with the J303 with without heat.

It takes a quarter turn with a straight edge screwdriver. Dependable, non-siphoning Durapride valve. Great value & great features don't have to come in a boring, boxy profile. Also, our patented ports on the sidewall of the valve cover allow heat dispersal...

You can mount this valve on the bottom or on the side and has a bouyancy equal to a 6" round float. It's design reduces stock damage & minimises blockage. Minimum inlet pressure 5 PSI, Maximum inlet pressure 150 PSI.