Livestock Waterers Farm Supplies For Sale In Independence

White styrofoam triangular disc float only.

This piece is held by two thumbscrews not included in this part. 3" orange arm that fits between the lower arm and the float connect.

This repair kit will fit in all Apex Valves & is made for use in all high pressure or low pressure applications.

B81 includes: Ref. B81 Hook, Rod, Cone and Nut Assembly for WFD85 and MFD85 field drinker. 6, 7 and 12 (see parts list in pictures attached)

#3 on breakdown. No lock pins or inner parts included. Pride of the Farm VP124 plastic valve body only.

SPI white corrugated baffle for model 4x4 energy free waterer.

Connect valve to 301 round float. A brass rod float arm 1/4" x 4" with threads on each end.

The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction tanks. If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch...

-Minimal Assembly -Strong Utra-violet Light Protection to prevent Fading/Cracking -One Inch (2.54 cm) Drain Plug (Drain is to the left as you face drinker) -Drinker Opening is: 14.0"(35.6 cm )W 16.5"(41.9 cm) H 12.0"(30.5 cm) D

Water line entry on either side with 1/2" brass fitting. Powder coated, anti-bacterial steel bowl has non-siphoning float to maintain constant water level. Use for horses, sheep, calves and other livestock.

#6 on breakdown. Pride of the Farm Rubber Diaphragm that fits between the orifice & the plunger on a VP124 valve.

A round float for Arkfeld,SPI or Mira Fount waterers.

The Megaflow is compact, robust and manufactured from non-corroding materials. Its diaphragm principle of operation allows the Megaflow to give flows of up to 90 gallons per minute.

Water enters the MiraFount at 45 to 48 degrees. Each model comes with anchors for mounting to concrete pad, pipe insulation, and a section of 3/4" PVC pipe. 24" X 36" X 18" Waterers work on the same principle as a thermos bottle.

Replacement drain plug for MiraFount Waterers.

FEATURES: Side, Bottom, Top Mounting Valve body screws apart by hand for easy servicing Flow stops when unscrewed for servicing Supplied with back-nut and seal washer Built in check valve Fully adjustable Float Angle Pressure range 0-150 PSI Low pressure...

This bolt package is for Models 101, 202 & 404 with or without heat.

The pressure plate is made of the same strong nylon material, and provides fresh, clean water. This non-siphoning bowl is extremely resistant to damage and is easy to keep clean. Made of Strangkolon-nylon material.

Jug Thermostat fits Models 101, 202, 303 & 404 with heat.

These are not included when ordering a base only. There are four base screws that hold the top base to the bottom base.

Extra supply line protection, patented water circulation, multiple constant flow and drain options. Water supply line enters through our unique tower. Float is easily adjustable for varying water levels, Spring loaded pin allows access panel to pop off...

This waterer has the same description as the J404 EXCEPT THIS UNIT HAS NO HEAT!

Horseshoe shaped 285 Watt element used in all Franklin galvanized waterers.

The 303 Riser Tube protects the water supply line from the cold by insulating it in urethane foam, and warming it with a low wattage heating element. Water and electric lines run underground below frost line.

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

No other parts come with the Cam Link. This is the arm that opens & closes the plunger. Pride of the Farm Cam Link locks to the VP124 valve body on the top side with a link pin. #2 on breakdown.

This quick release "D" clip is used on all of the New Generation Energy Free Waterers (4 per Unit) & on the Electric Waterer's inspection plates.