Farm Equipment Swine Equipment For Sale In Spokane

Used to convey mash, crumbles or small pellet feeds. With standard 348 RPM power unit. Maximum particle size = 5/32" dia. Chore-Time Model 75/HMC Flex Auger. I.D. = 1.44" O.D. = 2.38"

Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. Chore-Time Model 75 Single Straight-Out Lower Boot Assembly. This is a complete Lower Boot that will accomodate a Single M75 auger exiting the boot horizontal...

Chore-Time Model 75 Tube Connector Only (steel conn/PVC pipe)

Chore-Time Model 108 1.5HP , 230V, 1-Phase Replacement Motor. For use on the following power Units: CT325966, CT325982, and CT3259124

Honeywell Gas Valve, LP Gas, for "K" series or later Pilot Light "Classic" heaters.

Commonly used when repairing/replacing M55 pvc tubing. Chore-Time Model 55 PVC Coupler. This coupler is used to connect two pieces of M55 tubing together when there is no bell end available.

Gas Cock Valve, Manual Shut Off with 1/2" pipe nipple. All "Ag " heaters

Chore-Time Gearhead Assembly 348 RPM used in Model 75, 90, HMC, 125, & 108 systems. Uses CT6104 Pinion Gear with 1/2 HP and 3/4 HP motors and CT5046 with 1 HP motors.

Height is 36 1/2". Fuel it with LP or convert to natural gas. The mounting brackets will accommodate most steel, wood, concrete, and plastic water tanks. Trojan starts with a long-lasting heavy steel casing and finishes it with a tough, baked-on powder...

Our new mat is 30% more efficient then fiberglass mats and 80% more efficient than heat lamps. 108.5 watts per side Designed for all types of farrowing in new or remodeled barns, Kane heat mats can be installed on the surface of any type flooring providing...

Chore-Time Model 108 45D PVC Elbow

Chore-Time Model 75/HMC Driver Weldment Assembly. Assembly includes CT7704 Driver Weldment, CT7703 Aguer Clamp and Cap Screws.

Chore-Time Micro switch for Hopper Level Control.

Comes with boot, anchor and bearing assemblies, slide shut-off kit and side access door assembly. Chore-Time Model 55 Quad 30� Lower Boot Assembly. This is a complete Lower Boot that will accomodate a Four M55 augers exiting the boot at a 30� angle.

Pilot Light Orfice, (NG), for Classic 60/348, Classic 115/379, Classic 170/410

Chore-Time Model 55/75 Flex-Joint Ring. Must use CT6381 Drop Tube with this Flex-Joint Ring.

Chore-Time Model 90/HMC Tube Connector Only. Steel tube to Steel tube.

Fan Wheel, 10-3/4" x 4-7/8", for Classic 170/408/410

Comes with boot, anchor and bearing assemblies, slide shut-off kit and side access door assembly. Chore-Time Model 55 Twin 30� Lower Boot Assembly. This is a complete Lower Boot that will accomodate Two M55 augers exiting the boot at a 30� angle.

The Sensor plus also includes a built in heater to dissapate moisture around the sensor. Chore-Time Drop Multiflo Tube Switch w/Sensor Plus. The Sensor Plus Drop Tube Switch has a built in safety timer that allows the operator to set a Maximum Run Time...

Just what you need for small hog operations, 4H or FFA Projects, a galvanized 2 hole hog feeder.

Our new mat is 30% more efficient then fiberglass mats and 80% more efficient than heat lamps. Designed for all types of farrowing in new or remodeled barns, Kane heat mats can be installed on the surface of any type flooring providing the producer with...

Chore-Time Model 75/HMC Driver Weldment Only. Auger slips over tube and uses CT7703 Auger Clamp/

Chore-Time Model 90 Driver Weldment Only. Auger slips over tube and uses CT7703 Auger Clamp.

Thermostat, Unit Mount with Bracket, Stainles Steel, (less wiring) Used in all Side Draw Models, (not Guardians)

Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. Chore-Time Model 90 Model Parts Package. This Weldment will accept the M90 Tube.

Chore-Time Hopper Level Control for single phase power units. Mounts in the last feeder and will turn ssytem on and off depending on the level of feed in the last feeder.