Farm Equipment Swine Equipment For Sale In Santa Rosa

With standard 348 RPM power unit. Delivery Rate = 100 lb./min. Used to convey mash, crumbles or small pellet feeds. I.D. = 1.75" O.D. = 2.71" Maximum moisture content = 18%. Maximum particle size = 3/16" dia.

Auger slips over tube and uses CT7703 Auger Clamp. Chore-Time Model 90 Driver Weldment Only.

Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. This Weldment will accept the M90 Tube. Chore-Time Model 90 Model Parts Package.

This is the auger access door assembly that mounts in the side of a Chore-Time lower boot. Chore-Time Clean-Out Cover Assembly.

This is a complete Lower Boot that will accomodate a Single M108 auger exiting the boot horizontal to the ground. Does not include plastic upper transition boot. Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly.

This is the red plastic tube anchor that bolts to the control unit and accepts the pvc pipe. Chore-Time Model 90/HMC Tube Anchor Weldement.

Just what you need for small hog operations, 4H or FFA Projects, a galvanized 1 hole hog feeder.

Control Valve Replacement for Pilot Light Heaters upto and including Series "J"

Chore-Time Nylon Pulley Assembly

Attaches to the bottom of the control unit box and funnels feed into a round discharge. Chore-Time Model 75/90 Control Unit Funnel.

Control, Hot Surface Ignition

Clamps hold the Drop in place. Chore-Time Model 55 Drop Kit with Clamps.

This is the side plug on all Chore-Time Gearheads. Chore-Time Replacement 1/4 NPT Pipe Plug.

Works well on plastic or metal pipes in cold weather. After installation on your pipe, simply connect to any 110v electrical supply line or thermostat. Useful as a heat supplement on supply lines under livestock waterers.

This is the toggle switch that is located on the CT46051 Switch & Plate Assembly that comes with the New Style 46800- Control Units. Used on Flex Auger models 55/75/90/HMC Chore-Time Toggle Switch - 4 Prong.

Used under a drop to "Y" or split the feed from one drop tube in to 2 drop tubes. Chore-Time Model 55/75/MF "Y" Outlet.

Used on M75 Flex Auger sysems from 90' - 150' in length, M90 & HMC Flex Auger sysems from 40' - 90' in length and M108 Flex Auger Systems from 20' - 50' in length. Replacement parts: Motor = CT5051, Pinion Gear = CT5046, Gearhead = CT3261-7

Each Tube is 10' long. Chore-Time Model 55 PVC Tubing.

This is a complete Lower Boot that will accomodate Two M55 augers exiting the boot at a 30� angle. Does not include plastic upper transition boot. Comes with boot, anchor and bearing assemblies, slide shut-off kit and side access door assembly.

Also used on Model 108 Anchor & Bearing Assembly Chore-Time Flex Auger Clamp for Model 75/90/HMC Driver Weldment at Control Unit.

This clamp is to be used to clamp the anchor bearing assembly to the boot. Chore-Time Model 55 Tube Clamp.

This is the lower boot body only. For a complete lower boot use part number CT9315 Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc.

With standard 348 RPM power unit. Maximum particle size = 3/16" dia. Used to convey high moisture corn, large pellets, shelled corn or ground feed. Delivery Rate = 220 lb./min. Maximum moisture content = 27%.

Long anchor tube on this assembly allows for more controlled flow into the auger. Chore-Time Model 90 Anchor & Bearing Assembly.

Chore-Time Micro switch for Hopper Level Control.

Supply Hose, LP Gas, 1/4" X 10', for Classic 60/346, (20543)

This feeder is easy to fill, made of 20 ga. G90 Galvanized steel, has a flapper rain cover, 2 feed holes & holds approximately 150 pounds of feed. Made in the near by state of Missouri, here is a hog feeder for your 4H project or small producers raising...