Farm Equipment Swine Equipment For Sale In Salinas

Screen filter keeps foreign matter out of valve. Precision machined tapered threads create a water-tight union. Sharp, deep teeth penetrate bite, improving bonding. Install connector and locknut, then screw in Model 75 nipple using pipe thread tape or...

The state of the art controller will maintain any pre-selected temperature between 68 degrees F and 95 degrees F (20 degrees C and 35 degrees C). It also incorporates a unique safety shutoff protector.

Chore-Time Multiflo Auger Connectors (2 per pkg)

Use with Model 55/75/90 Outlets and CT1932 Drop Tube. Chore-Time Model 55/75/90/HMC Drop Tube Pin.

This is the lower boot body only. Chore-Time Model 75 Twin Auger Boot Weldment Only. For a complete lower boot use part number CT36389 or CT 36390 Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc.

Mount this unit under livestock waterers. An efficient way to revent freezing. An adjustable automatic thermostat permits you to control the temperature for whatever the condition.

This clamp is to be used to clamp the pvc tube to the control unit assembly. Chore-Time Model 55 Tube Clamp.

Fuel it with LP or convert to natural gas. Includes LP Hook up. This AGA approved system generates 12,400 BTU per hour if needed. This heater performs dependably in harsh winter conditions.

Also used on Model 108 Anchor & Bearing Assembly Chore-Time Flex Auger Clamp for Model 75/90/HMC Driver Weldment at Control Unit.

This coupler is used to connect two pieces of M55 tubing together when there is no bell end available. Chore-Time Model 55 PVC Coupler. Glued into place with PVC cement. Commonly used when repairing/replacing M55 pvc tubing.

Used under a drop to "Y" or split the feed from one drop tube in to 2 drop tubes. Chore-Time Model 55/75/MF "Y" Outlet.

Even the smallest pgis like the easy bite trigger and tapered end on the Spiglet. Ideal for farrowing stalls, creep areas and nurseries. 5/8" Bite on Water Supply Trigger. The Spiglet reduces spray waste by directing the nipple into the mouth.

This is the toggle switch that is located on the CT46051 Switch & Plate Assembly that comes with the New Style 46800- Control Units. Used on Flex Auger models 55/75/90/HMC Chore-Time Toggle Switch - 4 Prong.

Chore-Time Model 90 Direct Drive Control Unit, 1Phase

Chore-Time Nylon Pulley Assembly

This is a complete Lower Boot that will accomodate Two M90 augers exiting the boot horizontal to the ground. Chore-Time Model 90 Twin Straight-Out Lower Boot Assembly. Does not include plastic upper transition boot.

CT5046R Pinion has 21 teeth and a 1/2" diameter bore. Chore-Time Replacement Pinion Gear.

This feeder is easy to fill, made of 20 ga. G90 Galvanized steel, has a flapper rain cover, 2 feed holes & holds approximately 150 pounds of feed. Made in the near by state of Missouri, here is a hog feeder for your 4H project or small producers raising...

The vinyl coated fiberglass shaft extends completely thru this nw paddle head & into the end of the poker tip making the Rattle Paddle more durable for longer life. The Stix & Paddle shafts are made of a vinyl coated fiberglass to eliminate shattering...

This is the lower boot body only. Chore-Time Model 55 Twin Auger Boot Weldment Only. For a complete lower boot use part number CT9314 Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc.

This is a complete Lower Boot that will accomodate Two M55 augers exiting the boot at a 30� angle. Chore-Time Model 55 Twin 30� Lower Boot Assembly. Does not include plastic upper transition boot.

Big enough for sows, yet small enough for baby pigs. Trojan's Cast Aluminum with baked on powder coat finish. Stainless-Steel trip plate & housing. All Models use the same tried & proven non-siphoning trouble free 393 valve.

NG Orfice, Burner, for Classic 115/379

Maximum particle size = 3/16" dia. Used to convey high moisture corn, large pellets, shelled corn or ground feed. Delivery Rate = 220 lb./min. Maximum moisture content = 27%. Chore-Time Model 108 Flex Auger.

This is the bearing assembly used on CT35346 & CT35347 Anchor & Bearing Assemblies manufactured since May 1996. Chore-Time Model 75 Bearing Cap Assembly.

Contains hose, 06654 adapter. Supply Hose, 3/8" x 10' for Models Guardian60/100, Classic 60N, 115, 115N, 40 (NG).

Motor, Totally Enclosed, Ball Bearing, 1/8 HP, Guardian 100, AW075