Farm Equipment Swine Equipment For Sale In Pembroke Pines

21" Thermocoupler "Snap In" for all LB White Pilot Light Heaters

Dosatron's D128R, 7 Gallon, Flat Top Injector has withstood the test of time. Over 30 years of field experience have shown this to be the Injector of choice for most producers.

Chore-Time Model 75 Anchor & Bearing Assembly (CT #37346). Long anchor tube on this assembly allows for more controlled flow into the auger.

Kane's unique design maintains the optimal temperature for your farrowing environment to reduce stress, improve digestion, and promote rapid growth.� NRTL, CSA/US approved. Our new mat is 30% more efficient then fiberglass mats and 80% more efficient...

72 watts, NRTL, CSA/US approved. They will cause the heat mat to overheat. Perfect for outdoor pens, kennels, garages, dog houses, whelping areas, veterinary clinics, and barns. Warning: heat radiating appliance for animals - always use a temperature...

NG Orfice, Burner, for Classic 115/379

Chore-Time Model 90/HMC PVC Tubing. Each tube is 10' long.

Chore-Time Model 75 Tube Connector w/Clamps

The Sensor Plus Drop Tube Switch has a built in safety timer that allows the operator to set a Maximum Run Time for the auger to ensure that it will not continue to operate if the feed bin runs out of feed or if a drop tube is knocked out of a feeder.

LP Orfice, Burner, for Classic 115/377

Supply Hose, LP Gas, 1/4" X 10', for Classic 60/346, (20543)

Chore-Time Model 75 Tube Connector Only

Pilot Light Orfice, (NG), for Classic 60/348, Classic 115/379, Classic 170/410

Chore-Time Model 75/90/HMC 1/2HP, 230V, 1-Phase Replacement Motor. For use on the following power Units: CT325950, CT325951 and CT325977

Honeywell Gas Valve, NG Gas, for "K" series or later Pilot Light "Classic" heaters.

Chore-Time Boot Bearing Assembly. Used on Chore-Time M75 Auger Boots prior to 1996 and M125 Boots

Replacement parts: Motor = CT8782, Pinion Gear = CT6104, Gearhead = CT32617 Used on M108 Flex Auger Systems from 110' - 150' in length. Chore-Time Model 108 1.5HP, 348 RPM, 230v, 60HZ, 1PH Power Unit.

This is a complete Lower Boot that will accomodate a Single M75 auger exiting the boot at a 30� angle. Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly.

Igniter only, no bracket, for HSI and Guardian heaters, (509201)

Stainless Steel U-bolt for easy adjustment of nipple height. Built tough to resist hog abuse. A painted bracket permits you to attach water pipe to wall or paneling.

Includes LP Hook up. Fuel it with LP or convert to natural gas. The mounting brackets will accommodate most steel, wood, concrete, and plastic water tanks. The control and burner assembly removes easily for service through the hinged cover.

Thermostat, Unit Mount with Bracket, Stainles Steel, (less wiring) Used in all Side Draw Models, (not Guardians)

Air Proving Switch, used in models: AB200, AB250, AW075, AW215, AW230, AW250,AW325, Classic 115, 170 (G-K Series)

Chore-Time Model 90 Anchor & Bearing Assembly. Long anchor tube on this assembly allows for more controlled flow into the auger.

This is the lower boot body only. Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc. Chore-Time Model 55 Quad Auger Boot Weldment Only.

Mount this unit under livestock waterers. It runs on LP or convert to natural gas, developing 4050 BTU per hour. An efficient way to revent freezing. An adjustable automatic thermostat permits you to control the temperature for whatever the condition.

Motor, Totally Enclosed, Ball Bearing, 1/8 HP, Guardian 100, AW075