Farm Equipment Swine Equipment For Sale In Nashville Davidson

Chore-Time Model 90/HMC Plastic Drop Tube (3 3/4" x 12')

Use with Model 55/75/90 Outlets and CT1932 Drop Tube. Chore-Time Model 55/75/90/HMC Drop Tube Pin.

Attaches to the bottom of the control unit box and funnels feed into a round discharge. Chore-Time Model 75/90 Control Unit Funnel.

Short anchor tube on this assembly allows for less restriction and more flow into the auger. Chore-Time Model 90 Anchor & Bearing Assembly.

Chore-Time Model 55 Twin Auger Boot Weldment Only. For a complete lower boot use part number CT9314 Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc.

Chore-Time Model 75 Direct Drive Control Unit, 1Phase

Chore-Time Model 75 Tube Connector Only

Uses the Tip Plate Assembly. Trojan's Cast Aluminum Cup featuring the 290 Gravity Valve. Great for use on tank or barrel installations.

Designed for all types of farrowing in new or remodeled barns, Kane heat mats can be installed on the surface of any type flooring providing the producer with maximum flexibility and energy savings when heating crates, free stall, and comfort stall creep...

Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. Chore-Time Model 90 Model Parts Package. This Weldment will accept the M90 Tube.

Chore-Time Model 90 Single 30� Lower Boot Assembly. Does not include plastic upper transition boot. Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly.

For use on the following power Units: CT325952, CT325978, CT3259122 and CT3259136 Chore-Time Model 55/75/90/108 3/4HP, 230V, 1-Phase Replacement Motor.

Slide shut-off assembly used on Model 75/90 Twin Boots, two auger systems. Chore-Time Model 75/90 Twin Slide Assembly. Includes hardware.

Over 30 years of field experience have shown this to be the Injector of choice for most producers. Dosatron's D128R, 7 Gallon, Flat Top Injector has withstood the test of time.

Motor, Totally Enclosed with Sleeve Bearing, 1/15 HP, Classic 60/346/348

Chore-Time Replacment Oil Seal (Output Shaft) for All Chore-Time Gearheads

This is the side plug on all Chore-Time Gearheads. Chore-Time Replacement 1/4 NPT Pipe Plug.

Clamps hold the Drop in place. Chore-Time Model 55 Drop Kit with Clamps.

I.D. = .89" O.D. = 1.52" Delivery Rate = 15 lb./min. Chore-Time Model 55 Flex Auger. With standard 348 RPM power unit. Used to convey mash, crumbles or small pellet feeds. Maximum moisture content = 18%.

Chore-Time Model 55 Suspension Kit. Quantity needed is determined by the length of the M55 auger system. Each kit includes 3 "S" Hooks, 10' of double loop chain. Used to suspend the M55 Flex Auger from the ceiling.

Pilot Light shield for Classic 115/377/379

Chore-Time Model 90/HMC 45� PVC Elbow

Chore-Time Drop Multiflo Tube Switch w/Sensor Plus. This helps reduce the build up of dust and dirt on the sensor that can lead to false readings. The Sensor plus also includes a built in heater to dissapate moisture around the sensor.

Chore-Time Model 55 Quad Auger Boot Weldment Only. For a complete lower boot use part number CT9315 Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc.

Chore-Time Model 108 Single Straight-Out Lower Boot Assembly Only. Does not include plastic upper transition boot. Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly.

Short anchor tube on this assembly allows for less restriction and more flow into the auger. Chore-Time Model 108 Anchor & Bearing Assembly.

This is the red plastic tube anchor that bolts to the control unit and accepts the pvc pipe. Chore-Time Model 90/HMC Tube Anchor Weldement.