Farm Equipment Swine Equipment For Sale In Mckinney

G90 Galvanized steel, has a flapper rain cover, 2 feed holes & holds approximately 150 pounds of feed. This feeder is easy to fill, made of 20 ga. Made in the near by state of Missouri, here is a hog feeder for your 4H project or small producers raising...

Does not include plastic upper transition boot. Chore-Time Model 75 Single 30� Lower Boot Assembly. This is a complete Lower Boot that will accomodate a Single M75 auger exiting the boot at a 30� angle.

Chore-Time Model 108 45D PVC Elbow

Stainless steel bracket, bolts, nuts, washers & 45 degree elbow. Our Model 2000 Wrench Curve Nipple is standard & it's 45 degree angle keeps the pigs standing while drinking. The cup catches the excess water reducing water waste.

5/8" Bite on Water Supply Trigger. The Spiglet reduces spray waste by directing the nipple into the mouth. Ideal for farrowing stalls, creep areas and nurseries. The wrench flats make installation an easy task for this one piece body that fits standard...

Chore-Time Model 75 Tube Clamp (Steel)

This is the red plastic tube anchor that bolts to the control unit and accepts the pvc pipe. Chore-Time Model 75 Tube Anchor.

Control Valve Replacement for Pilot Light Heaters upto and including Series "J"

Used at the end of a Drop Feeding system to control the operation of the power unit. Chore-Time Model 75 Mechanical Drop Feeder Control Unit.

Clamps hold the Drop in place. Chore-Time Model 75 Drop Kit with Clamps.

Great for use on tank or barrel installations. Uses the Tip Plate Assembly. Trojan's Cast Aluminum Cup featuring the 290 Gravity Valve.

Does not include plastic upper transition boot. Chore-Time Model 90 Single Straight-Out Lower Boot Assembly. This is a complete Lower Boot that will accomodate a Single M90 auger exiting the boot horizontal to the ground.

This is the bearing assembly used on CT35346 & CT35347 Anchor & Bearing Assemblies manufactured since May 1996. Chore-Time Model 75 Bearing Cap Assembly.

Used under a drop to "Y" or split the feed from one drop tube in to 2 drop tubes. Chore-Time Model 55/75/MF "Y" Outlet.

Assembly includes CT7704 Driver Weldment, CT7703 Aguer Clamp and Cap Screws. Chore-Time Model 75/HMC Driver Weldment Assembly.

Mounts in the last feeder and will turn ssytem on and off depending on the level of feed in the last feeder. Chore-Time Hopper Level Control for single phase power units.

Each Tube is 10' long. Chore-Time Model 55 PVC Tubing.

This kit made to mount the Trojan water swing includes 6 feet of chain, 2 S-Hooks, 1 Screw Hook and 2 - A7900 Trojan Model 2000 Wrench Curve Nipples.

Replacement parts: Motor = CT5051, Pinion Gear = CT5046, Gearhead = CT3261-7 Used on M75 Flex Auger sysems from 90' - 150' in length, M90 & HMC Flex Auger sysems from 40' - 90' in length and M108 Flex Auger Systems from 20' - 50' in length.

This helps reduce the build up of dust and dirt on the sensor that can lead to false readings. Chore-Time Drop Multiflo Tube Switch w/Sensor Plus. The Sensor Plus Drop Tube Switch has a built in safety timer that allows the operator to set a Maximum Run...

Clamps hold the Drop in place. Chore-Time Model 55 Drop Kit with Clamps.

Chore-Time Multiflo Auger Connectors (2 per pkg)

Auger slips over tube and uses CT7703 Auger Clamp/ Chore-Time Model 75/HMC Driver Weldment Only.

This is the side plug on all Chore-Time Gearheads. Chore-Time Replacement 1/4 NPT Pipe Plug.

Motor, Totally Enclosed with Sleeve Bearing, 1/15 HP, Classic 60/346/348

Chore-Time Model 55/MF Tube Clamp

(Old number CT7114) Used on CT46800 Control units. Chore-Time Micro Switch for CT46051 Switch Assembly.