Farm Equipment Swine Equipment For Sale In Jackson

Chore-Time Multiflo Nylon 90� Elbow with Coupler & Clamps.

Easy-to-read feed level adjustment allows feeding individual amounts from 3/4 to 10 pounds (0.3 to 4.5 kg). Enable multiple feedings per sow per day by automating drop feeders with one of the proven CHORE-TIME � Winch systems.

Mounts in the last feeder and will turn ssytem on and off depending on the level of feed in the last feeder. Chore-Time Hopper Level Control for single phase power units.

This is the lower boot body only. Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc. For a complete lower boot use part number CT9313

Chore-Time Model 90/HMC Tube Connector w/Clamps

This is a complete Lower Boot that will accomodate a Single M75 auger exiting the boot at a 30� angle. Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly.

This feeder is easy to fill, made of 20 ga. Made in the near by state of Missouri, here is a hog feeder for your 4H project or small producers raising a few head of livestock. G90 Galvanized steel, has a flapper rain cover, 2 feed holes & holds approximately...

Chore-Time Model 75 Tube Connector w/Clamps

Chore-Time Model 90/HMC 45� PVC Elbow

Slide shut-off assembly used on Model 75/90 Twin Boots, two auger systems. Chore-Time Model 75/90 Twin Slide Assembly. Includes hardware.

For use on the following power Units: CT325952, CT325978, CT3259122 and CT3259136 Chore-Time Model 55/75/90/108 3/4HP, 230V, 1-Phase Replacement Motor.

Chore-Time Replacment Oil Seal (Pinion Side) for Gearheads CT32611, CT32612, CT32616 & CT32618

LP Orfice, Burner, for Classic 170/408

Rounded hand grips on the top and side make for easy handling. These double panels are perfect for large alleyways, pens and stand alone tasks such as marking and medicating. Light weight and small, its perfect for younger members of your crew and can...

This is the toggle switch that is located on the control unit (220v, single phase). Chore-Time DPST Toggle Switch-4 Prong. Used on Flex Auger models 55/75/90/HMC Older Style Metal Control Unit (Part Numbers 6500-).

Pilot Light Sheild, used in Classic 60K, 346 and 348 heaters.

Chore-Time Diaphragm Assembly for CT46051 Switch Assembly

Short anchor tube on this assembly allows for less restriction and more flow into the auger. Chore-Time Model 90 Anchor & Bearing Assembly.

Assembly includes CT7704 Driver Weldment, CT7703 Aguer Clamp and Cap Screws. Chore-Time Model 75/HMC Driver Weldment Assembly.

Supply Hose, LP Gas, 1/4" X 10', for Classic 60/346, (20543)

Rack and Pinion style Slide Shut-Off assembly for Twin (2) Auger Boots. Chore-Time Twin Manual Slide Assembly. Telescoping Drive Tube/Handle also available CT47638

Valve, Gas control, (LP Gas), 11" W.C., use in AW215CH, AW230EH, FH; All Guardian Models

Kane�s polyethylene heat mats installed with�thermostat controls are simply the most energy efficient heat mats in the world.� Kane thermostats reduce power consumption by an additional 50% of the rated watts per crate listings.� Designed for...

This is a complete Lower Boot that will accomodate a Single M55 auger exiting the boot at a 30� angle. Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly.

Easy-to-read feed level adjustment allows feeding individual amounts from 3/4 to 10 pounds (0.3 to 4.5 kg). Enable multiple feedings per sow per day by automating drop feeders with one of the proven CHORE-TIME � Winch systems.

Driver tube is the piece the Flex Auger slides over and attached to. Chore-Time Model 55 Driver Tube. Located at the control unit end of the Flex Auger syystem.

Used on Flex Auger sysems from 160' - 250' in length. Chore-Time Model 55 1/2 HP, 348 RPM, 60HZ-1PH 230V Power Unit. Replacement parts: Motor = CT5703, Pinion Gear = CT5046, Gearhead = CT32615