Farm Equipment Swine Equipment For Sale In Irving

This feeder is easy to fill, made of 20 ga. Made in the near by state of Missouri, here is a hog feeder for your 4H project or small producers raising a few head of livestock. G90 Galvanized steel, has a flapper rain cover, 2 feed holes & holds approximately...

Chore-Time Model 108 Anchor & Bearing Assembly. Long anchor tube on this assembly allows for more controlled flow into the auger.

Chore-Time Model 108 Plastic Drop Tube (5" x 12')

Chore-Time Model 90 Anchor & Bearing Assembly. Long anchor tube on this assembly allows for more controlled flow into the auger.

I.D. = .89" O.D. = 1.52" Delivery Rate = 15 lb./min. Maximum moisture content = 18%. With standard 348 RPM power unit. Chore-Time Model 55 Flex Auger. Used to convey mash, crumbles or small pellet feeds.

Chore-Time Model 75/HMC Driver Weldment Assembly. Assembly includes CT7704 Driver Weldment, CT7703 Aguer Clamp and Cap Screws.

Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. Chore-Time Model HMC Model Parts Package. This Weldment will accept the HMC Tube.

The state of the art controller will maintain any pre-selected temperature between 68 degrees F and 95 degrees F (20 degrees C and 35 degrees C). The ESU Electronic Temperature Controller is a thermostatic control device that allows you to select and...

Pilot Assembly with LP Orfice for Classic heaters

Install connector and locknut, then screw in Model 75 nipple using pipe thread tape or pipe dope (not included). Sealing ring resists buckling or slipping during installation, and provides a complete 360° seal.

LP Orfice, Burner, for Classic 170/408

Each kit includes 25 "S" Hooks, 12 Screw Hooks and 25' of double loop chain. Chore-Time Model 75/90/HMC /108 Suspension Kit. Used to suspend the Flex Auger from the ceiling. Quantity needed is determined by the size and length of the auger system.

Chore-Time Model 75 Drop Kit with Clamps. Clamps hold the Drop in place.

The Sensor plus also includes a built in heater to dissapate moisture around the sensor. Chore-Time Universal Drop Tube Switch w/Sensor Plus & Safety Timer. The Sensor Plus Drop Tube Switch has a built in safety timer that allows the operator to set a...

Chore-Time Model 55 Anchor & Bearing Assembly. Long anchor tube on this assembly allows for more controlled flow into the auger.

Chore-Time Gearhead Assembly 348 RPM used in Model 75, 90, HMC, 125, & 108 systems. Uses CT6104 Pinion Gear with 1/2 HP and 3/4 HP motors and CT5046 with 1 HP motors.

Chore-Time Model 75/90 Control Unit Funnel. Attaches to the bottom of the control unit box and funnels feed into a round discharge.

The vinyl coated fiberglass shaft extends completely thru this nw paddle head & into the end of the poker tip making the Rattle Paddle more durable for longer life. Koehn 1/2" x 42" Original Grip Rattle Paddle with BB's inside to help animals move along...

Chore-Time Model 75 45� PVC Elbow

Used on CT46800 Control units. Chore-Time Micro Switch for CT46051 Switch Assembly. (Old number CT7114)

Built tough to resist hog abuse. A painted bracket permits you to attach water pipe to wall or paneling. Stainless Steel U-bolt for easy adjustment of nipple height.

Theromostat & controls may be removed easily for service. This heater performs dependably in harsh winter conditions. Trojan starts with a long-lasting heavy steel casing and finishes it with a tough, baked-on powder coat finish.

Include the Tube Anchor Plate Weldment, Clamp and Hardware to bolt to the Control Unit. Chore-Time Model 90 Model Parts Package. This Weldment will accept the M90 Tube.

These double panels are perfect for large alleyways, pens and stand alone tasks such as marking and medicating. Designed to move animals with ease, Kane sorting boards are light weight yet extremely durable.

Control, Hot Surface Ignition

Chore-Time Replacement 1/4 NPT Pipe Plug. This is the side plug on all Chore-Time Gearheads.

Chore-Time Model 108 Direct Drive Control Unit, 1Phase