Replacement parts: Motor = CT6857, Pinion Gear = CT6104, Gearhead = CT32617 Used on M75 Flex Auger sysems from 160' - 200' in length, M90 & HMC Flex Auger sysems from 100' - 50' in length and M108 Flex Auger Systems from 60' - 100' in length.
Located at the control unit end of the Flex Auger syystem. Driver tube is the piece the Flex Auger slides over and attached to. Chore-Time Model 55 Driver Tube.
Commonly used when repairing/replacing M55 pvc tubing. This coupler is used to connect two pieces of M55 tubing together when there is no bell end available. Chore-Time Model 55 PVC Coupler.
Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accomodate a Single M108 auger exiting the boot at a 30� angle.
This heater performs dependably in harsh winter conditions. Includes LP Hook up. Fuel it with LP or convert to natural gas. Theromostat & controls may be removed easily for service.
The Stix & Paddle shafts are made of a vinyl coated fiberglass to eliminate shattering & splintering and has a 180 degree flexibility. The vinyl coated fiberglass shaft extends completely thru this nw paddle head & into the end of the poker tip making...
Chore-Time Model 55/75/90/108 3/4HP, 230V, 1-Phase Replacement Motor. For use on the following power Units: CT325952, CT325978, CT3259122 and CT3259136
Comes with boot, anchor and bearing assemblies, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accomodate Two M90 augers exiting the boot horizontal to the ground.
Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accomodate a Single M75 auger exiting the boot horizontal to the ground.
Kane�s polyethylene heat mats installed with�thermostat controls are simply the most energy efficient heat mats in the world.� Kane thermostats reduce power consumption by an additional 50% of the rated watts per crate listings.� Designed for...
Kane�s polyethylene heat mats installed with�thermostat controls are simply the most energy efficient heat mats in the world.� Kane thermostats reduce power consumption by an additional 50% of the rated watts per crate listings.� Designed for...
Kane�s polyethylene heat mats installed with�thermostat controls are simply the most energy efficient heat mats in the world.� Kane thermostats reduce power consumption by an additional 50% of the rated watts per crate listings.� Designed for...
Enable multiple feedings per sow per day by automating drop feeders with one of the proven CHORE-TIME � Winch systems. Easy-to-read feed level adjustment allows feeding individual amounts from 3/4 to 10 pounds (0.3 to 4.5 kg).
Replacement parts: Motor = CT5051, Pinion Gear = CT5046, Gearhead = CT3261-7 Used on M75 Flex Auger sysems from 90' - 150' in length, M90 & HMC Flex Auger sysems from 40' - 90' in length and M108 Flex Auger Systems from 20' - 50' in length.
Prevent water lines from freezing. After installation on your pipe, simply connect to any 110v electrical supply line or thermostat. 100W, 110v heating element installs on any pipe, plastic or metal, in less that one minute using the two springs attached...
Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accomodate a Single M108 auger exiting the boot horizontal to the ground.
Replacement parts: Motor = CT8782, Pinion Gear = CT6104, Gearhead = CT32617 Used on M108 Flex Auger Systems from 110' - 150' in length. Chore-Time Model 108 1.5HP, 348 RPM, 230v, 60HZ, 1PH Power Unit.
Comes with boot, anchor and bearing assembly, slide shut-off kit and side access door assembly. This is a complete Lower Boot that will accommodate a Single HMC auger exiting the boot at a 30� angle.
Does Not include anchor & bearing assembly, clean-out cover assembly, cannon ball, slide shut-off kit, etc. This is the lower boot body only. Chore-Time Model 55 Twin Auger Boot Weldment Only.