Farm Equipment Livestock Waterers For Sale In Yonkers

600 watt x 120 volt heating element only Arkfeld waterer element replacement.

Optional heater, 250 watts, 110 volts. Stainless steel access plates. Drinker is very easy to clean-no disassembly for cleaning required. Simple water level adjustment, easy to clean.

This piece is held by two thumbscrews not included in this part. 6 1/2" orange arm that fits between the lower arm and the float connect.

1 year warranty. It features a heavy duty anti-chew cord protector & operates efficiently at the bottom of the tank; unnoticed by livestock. SAFE IN PLASTIC TANKS. Farm Innovator's Submergible 1500 Watt Tank De-Icer operates automatically only during...

ICE-N-EASY 1500W, thermostatically controlled to operate only when necessary. THIS UNIT IS FOR METAL TANKS ONLY. Farm Innovators floating tank de-icer has a heavy duty anti-chew cord protector with a 1 year guarantee.

Robert's Brass 1/2" plunger only for replacement in existing 1/2" valve.

It has an above water float adjustment, cord cleat for shutting off valve and a 1 1/2" water level differential from open to close. It's design reduces stock damage and minimises blockage.

It moves the upper arm and is also held by thumbscrew to the float arm. The lower arm is blue and is located in the bottom bracket of the top base and is held by a lock pin.

This quick release "D" clip is used on all of the New Generation Energy Free Waterers (4 per Unit) & on the Electric Waterer's inspection plates.

1/2" orfice only for the inside of a Franklin Valve.

This diaphragm fits all Jug Model Valves.

The tank also comes with a 1.25" drains installed. 3 year warranty. All edges have been rounded for safety & strength. If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch...

-Minimal Assembly -Strong Utra-violet Light Protection to prevent Fading/Cracking -One Inch (2.54 cm) Drain Plug (Drain is to the left as you face drinker) -Drinker Opening is: 14.0"(35.6 cm )W 16.5"(41.9 cm) H 12.0"(30.5 cm) D

600 watt x 240 volt heating element with surface mount thermostat included. Arkfeld waterer element & thermostat replacement.

The orange cap only that fits over the insides of the Franklin Valve.

Unit is unnoticed by livestock - no cord in water. Thermostatically controlled to only run when necessary. Custom made to use in all Rubbermaid stock tanks with 1500 Watts of power.

45 Gallon, 48" x 35" x 25" - 1345# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

#5 on breakdown. Pride of the Farm Plastic Plunger that fits directly into the VP124 valve body & the rubber diaphragm.

250W heater, 2" built in drain, overflow port can be used either as an internal drain or it can be used for optional continuous flow operation, rugged notches for secure anchoring & spring loaded pin allows easy removal of access panel.

#4 on breakdown The connect the Cam & Power Link to the VP124 valve body. You will need 2 per valve assembly. Pride of the Farm Link pin only.

They can also be easily stacked for deeper installations. It has an excellent insulating property of R15 and amazing structural strength. The SPI Insulated Earth Tube conserves the earth ground source heat as it rises up the vertical shaft to help protect...

A drain plug for Arkfeld waterers - 2" in size - Cork.

Suggested where sugar sand is a problem in the water supply. Robert's Brass 3/4" sand plunger only for replacement in existing 3/4" valve.

Must be used with part #400267 Plunger Only. This black seat fits inside the plunger and shuts off the water through the orfice.