Farm Equipment Livestock Waterers For Sale In Scottsdale

The 303 Riser Tube protects the water supply line from the cold by insulating it in urethane foam, and warming it with a low wattage heating element. Water and electric lines run underground below frost line.

Robert's 3/4" rubber cup ring that fits on the brass plunger.

This model features an adjustable short arm for customizing water level. Robert's Brass 3/4" orifice Valve complete with plunger and arms. The R400 series is a high-capacity float valve with male NPT inlet and outlet connections.

#5 on breakdown. Pride of the Farm Plastic Plunger that fits directly into the VP124 valve body & the rubber diaphragm.

The orange cap only that fits over the insides of the Franklin Valve.

Thermostatically controlled to only run when necessary. Guaranteed for 1 year & SAFE IN PLASTIC. This donut shaped 500 Watt De-Icer is designed for multiple uses around the farm. Constructed of Cast Aluminum for ultimate effiency & safety.

Robert's Brass 3/4" orfice Valve complete with sand plunger and arms.

It has an above water float adjustment, cord cleat for shutting off valve and a 1 1/2" water level differential from open to close. Minimum inlet pressure 5 PSI, Maximum inlet pressure 150 PSI.

This quick release "D" clip is used on all of the New Generation Energy Free Waterers (4 per Unit) & on the Electric Waterer's inspection plates.

This unit fits the Model 101, 202 & 404 with or without heat.

#11 on breakdown. Pride of the Farm Plastic Thumb Screw that connects the Power Link & the Float arm (not included).

Unit is unnoticed by livestock - no cord in water. Guaranteed for 1 year & SAFE IN PLASTIC. Custom made to use in all Rubbermaid stock tanks with 1500 Watts of power. Thermostatically controlled to only run when necessary.

1/2" orfice only for the inside of a Franklin Valve.

Blue 10 3/4" replacement ball for the Mira Fount 3354S, M3370S, M3390, M3390E cattle waterers & 3360-10 hog waterer.

A round float for Arkfeld,SPI or Mira Fount waterers.

Nature's ground water temperature does this job. Tolerance to water level - you don't have to worry about summer & winter water levels. Sealed bottom keeps out moisture & rodents. No pulleys & cable to foul & rust.

It measures 3.25" x 4.25" x 2.38". Pride of the Farm White Poly Float that screws into the float arm & turns the water off & on in your waterers.

Connects valve to 301 round float. A brass rod float arm 1/4" x 6" with threads on each end.

#10 on breakdown. Pride of the Farm Plastic Nut Only that holds the base & plunger tight inside the Valve Body.

Often used in Franklin & Arkfeld waterers. Surface mount thermostat used in galvanized waterers. Turns on at 36 degrees and turns off at 48 degrees.

-Minimal Assembly -Strong Utra-violet Light Protection to prevent Fading/Cracking -One Inch (2.54 cm) Drain Plug (Drain is to the left as you face drinker) -Drinker Opening is: 14.0"(35.6 cm )W 16.5"(41.9 cm) H 12.0"(30.5 cm) D

This model features an adjustable short arm for customizing water level. Robert's Brass 1/2" orifice Valve complete with plunger and arms. The R400 series is a high-capacity float valve with male NPT inlet and outlet connections.

Suggested where sugar sand is a problem in the water supply. Robert's Brass 3/4" sand plunger only for replacement in existing 3/4" valve.

This unit has the same description as the J303 EXCEPT THIS UNIT HAS NO HEAT!

The MicroSweeper requires no maintenance, no electricity and no adjustment, EVER. It is a thermal sensing valve that is constatly in contact with the water & "intermittently" releases enough pressurized water to prevent surface ice as the water temperature...

Robert's 3/4" rubber plunger seat only.