Farm Equipment Livestock Waterers For Sale In Lincoln

It has an excellent insulating property of R15 and amazing structural strength. They can also be easily stacked for deeper installations. The dimensions of this tube is 12 3/4" OD x 49" tall with 2 1/2" of insulation.

This orange plunger holds the seat (not included) and is pushed by the upper arm towards or away from the orfice.

Weather seal Kit for Jug 101, 202 & 404 with or without heat. 1 per model EXCEPT 404 models need 2 kits.

Robert's Brass 3/4" plunger only for replacement in existing 3/4" valve.

Drinker is very easy to clean-no disassembly for cleaning required. Available in light gray. Optional heater, 250 watts, 110 volts. Our chamber can go as low as minus 30 degrees F (-34.4 degrees C).

The lower arm is blue and is located in the bottom bracket of the top base and is held by a lock pin. It moves the upper arm and is also held by thumbscrew to the float arm.

VP2 Valve Upgrade Kit for 1/8" Orifice Valve

A brass rod float arm 1/4" x 8" with threads on each end. Connects valve to 301 round float.

20 Gallon, 36" x 35" x 25" - 1060# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Blue plastic valve assembly fits a 3/4" FPT with a 3/4" orfice inlet. Mostly used on cattle waterers.

Blue octagon plunger that fits inside the Mira Fount cattle waterer valve.

Weather strip & an insulated sleeve for the supply line come with each unit. Seamless sidewall cannot leak. Sealed bottom keeps out moisture & rodents. Double wall DURAROCK construction contains hindered amine light stabilizer, the most effective ultraviolet...

450 watt heater, 3" wide x 2 1/4" tall x 11" long, adjustable theromstat multi purpose portable heater. Do Not Immerse into liquid.

#1 on breakdown. Pride of the Farm Power Link locks to the VP124 valve body with a link pin & then thumbscrews to the float arm. No other parts are included with this Power Link.

The 250W elemnt is encased in aluminum for durability & safety. Operates effecicently at the bottom of the bucket because warm water rises. SAFE IN PLASTIC. Farm Innovator's Ice Chaser operates automatically only during freezing temperatures.

Model VT100 valve delivers about 2 1/2 gallons (9.5 liters) per minute. Drinker is very easy to clean-no disassembly for cleaning required. Half moon design on back corner for securing up to a 2 inch (5.1 cm) PVC tube for plumbing from above or below.

Robert's 1/2" rubber cup ring that fits on the brass plunger.

Pride of the Farm Element for electric waterer units.

Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float. Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm.

Robert's Brass 1/2" orfice Valve complete with sand plunger and arms.

2" built in drain, stainless steel spring loaded attachment pins make cover removal & replacement easy, recessed, protected notches for secure anchoring, overflow port & dependable non-siphoning Durapride Valve.

Red octagon plunger that fits inside the Mira Fount cattle waterer RED valve.

The orange male fitting end of the Franklin Valve. No inside working parts included.

A brass rod float arm 1/4" x 6" with threads on each end. Connects valve to 301 round float.

Pride of the Farm Plastic Thumb Screw that connects the Power Link & the Float arm (not included). #11 on breakdown.

30 Watt Heater for J303 Corner Mount Horse Stall Waterers.