Farm Equipment Livestock Waterers For Sale In Chesapeake

No inside working parts included. This piece holds the plunger and upper arm. The inside base of the Franklin Valve.

Highly recommended for ALL cold climate installations. They can also be easily stacked for deeper installations. The dimensions of this tube is 12 3/4" OD x 49" tall with 2 1/2" of insulation.

Screw that holds the float connect to the top of the float.

Horseshoe shaped 285 Watt element used in all Franklin galvanized waterers.

The polyethylene used in our SPI Livestock Waterers is FDA and HPB approved, food grade, recyclable plastic. Engineered with the farmer in mind, this waterer allows easy access to submersible heater, water line, incoming services and provides effortless...

It is held by a float screw and connects on to the bottom of the float arm. Plastic piece that sits on top of the float.

45 Gallon, 48" x 35" x 25" - 1345# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

It moves the upper arm and is also held by thumbscrew to the float arm. The lower arm is blue and is located in the bottom bracket of the top base and is held by a lock pin.

This diaphragm fits all Jug Model Valves.

SPI 351/352 New Generation Gasket.

The peaked roof and raised ribs around the door openings prevent manure, feed and other contaminants from being washed into the bowl, and facilitates water run off. 5 year warranty.

A drain plug for the Arkfeld waterers - 1 1/2" in size - Black rubber.

If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction...

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Johnson Waterer Element Clips to hold the heating element.

SPI Drain Plug (#11) for all New Generation waterers.

This piece is held by two thumbscrews not included in this part. 3" orange arm that fits between the lower arm and the float connect.

Guaranteed for 1 year & SAFE IN PLASTIC. Thermostaically controlled to only run when necessary. Protective cage permits use in all tanks. The 1500 Watt element easily converts from a safe plastic floating de-icer into a submergible de-icer with a simple...

It is manually operated and when turned on allows a continuous flow of water through the valve to assist in the prevention of water freezing in the valve and pipe work supplying it.

If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction...

Connect valve to 301 round float. A brass rod float arm 1/4" x 4" with threads on each end.

Ideal for use in Ponds 50 to 600 gallons. Guaranteed for 3 years & SAFE IN PLASTIC, rubber liners or concrete. Thermostatically controlled to only run when needed. Constructed of Cast Aluminum for ultimate efficiency & safety.

Float Arm for the Mira Fount M3360, M3410, M3410-4, M3465 waterer.

#12-2 on the breakdown. This part number is for the arm only & is usually used on hog troughs. Pride of the Farm Plastic 2 1/2" Float arm is connected to the Power Link by a thumbscrew & then screws directly into the Poly float.

If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction...

-Minimal Assembly -Strong Utra-violet Light Protection to prevent Fading/Cracking -One Inch (2.54 cm) Drain Plug (Drain is to the left as you face drinker) -Drinker Opening is: 14.0"(35.6 cm )W 16.5"(41.9 cm) H 12.0"(30.5 cm) D

Grade A compliant. Pride of the Farm's trough drinker is a favorite for feed yards, pastures and dairies. Water supply line enters through our unique tower. The tower is foamed filled and the surrounding wall and valve cover are foam filled, Shutoff valve,...