Farm Equipment Livestock Waterers For Sale In Cedar Rapids

A brass rod float arm 1/4" x 12" with threads on each end. Connects valve to 301 round float.

This water caddy has come in handy for transporting water on trips as well as out to the field to water livestock. The only drawback is that if the nozzle is attached, I cannot close the tail gate on my truck.

#2 on breakdown. This is the arm that opens & closes the plunger. No other parts come with the Cam Link. Pride of the Farm Cam Link locks to the VP124 valve body on the top side with a link pin.

SPI 351/352 (old style) Rubber Drain Plug only .

No lock pins or inner parts included. Pride of the Farm VP124 plastic valve body only. #3 on breakdown.

There are four base screws that hold the top base to the bottom base. These are not included when ordering a base only.

Blue plastic valve assembly fits a 3/4" FPT with a .25" orfice inlet, includes arm that will fit any length, 2 thumbscrews & plastic float. Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm.

It has O'ring on one side & a Diaphragm on the other (not included). Pride of the Farm 5/32" Orifice on a VP124 Valve. #7 on breakdown.

Our drinker has foam filled double wall construction which adds to the efficiency. The Pride of the Farm "King" Energy Free drinker is beefy & ruggedly built but simple. 2" built in drain, stainless steel spring loaded attachment pins make cover removal...

Features High flow Compact robust construction 3/4″-2 1/2″ water level differential (increases as water pressure increases) Positive on/off operation Lock off with cord lock 5-150 PSI pressure rating Inlet filter Constructed from corrosion resistant...

Jug Thermostat fits Models 101, 202, 303 & 404 with heat.

Blue plastic valve assembly fits a 3/4" FPT with a .45" orfice inlet. Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm.

SPI 351/352 New Generation Gasket.

Thermostat ONLY for all Johnson Concrete Waterer Models.

Weather seal Kit for Jug 101, 202 & 404 with or without heat. 1 per model EXCEPT 404 models need 2 kits.

It will take abuse! Unaffected by ground movement due to freezing & thawing. 15" OD, corrugated plastic tubing insulated inside with Urethane foam to a 10" ID. Used to insulate the Heat Well below the frost line, preventing the loss of energy into the...

Replacement Plastic Valve & Float f/ WFD85 and MFD85 field drinkers.

Has many uses around the home & farm. Saves money by using power only when temperatures require. Five controlled temperatures (one just right for you) & no installation required. Operates with any 15 amp 120V electric heater or fan.

Black rubber seat to fit inside the Mira Fount Blue Plunger in a Mira Fount cattle waterer valve.

Arkfeld waterer element & thermostat replacement. 600 watt x 240 volt heating element with surface mount thermostat included.

A Brass short arm to connect the valve and the round float in Arkfeld and SPI waterers.

The lower arm is orange and is located in the bottom bracket of the top base and is held by a lock pin. It moves the upper to and is also held by a thumbscrew to the float arm.

The Topaz is compact, robust and manufactured from non-corroding materials. Topaz Float Valves are ideal for filling tanks where mounting above the water is preferred. Its diaphragm principle of operation allows the Topaz to give flows of up to 90 gallons...

Dimensions: 39" x 37" x 23" This Jug 4 Hole Waterer has a 45 gallon tank capacity & waterers 125 head of Dairy, 250 head of Beef & 300 head of Sheep. It's maximum 24-hr electical use is 1.56 kwh.