Farm Equipment Livestock Waterers For Sale In Cary

White styrofoam triangular disc float only.

Adjustable, submersible thermostat that can be turned as low as 10 degree turn on up to 80 degree turn off.

Pride of the Farm Cam Link locks to the VP124 valve body on the top side with a link pin. #2 on breakdown. This is the arm that opens & closes the plunger. No other parts come with the Cam Link.

600 watt x 240 volt heating element with surface mount thermostat included. Arkfeld waterer element & thermostat replacement.

SPI 90 degree elbow for all models.

Jug Thermostat fits Models 101, 202, 303 & 404 with heat.

If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole. 87" L x 62" W x 20" H 91# 5 Year warranty

Apex replacement float with string included.

Connects valve to 301 round float. A brass rod float arm 1/4" x 12" with threads on each end.

Connects valve to round float. A brass rod float arm 1/4" x 1" with threads on each end.

It will take abuse! 15" OD, corrugated plastic tubing. Won't rust, resists rot & holds up to chemically active soil conditions. Corrugated design provides rigidity without bulk when back filled with earth.

Mostly used on cattle waterers such as Franklin, SPI & MiraFount and Pride of the Farm. Blue plastic valve assembly fits a 3/4" FPT with a .25" orfice inlet.

All edges have been rounded for safety & strength. 28 1/2" x 20" x 10 1/4" Available in Aqua Blue color only. The larger tanks come with 1.25� drains installed. If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it...

I found the stated 50 gallon water capacity ends up being 35 gallons. The only drawback is that if the nozzle is attached, I cannot close the tail gate on my truck. A great way to carry more water for my RV 5th Wheel.

Suggested where sugar sand is a problem in the water supply. Robert's Brass 3/4" sand plunger only for replacement in existing 3/4" valve.

Heating element ONLY for the Johnson Concrete Model J360.

These are not included when ordering a base only. There are four base screws that hold the top base to the bottom base.

It is not adjustable for temperature. Unlike the original concept of the submerged bulb to sense water temperature, this unit senses the air temperature immediately surrounding the water basin, therefore, it is not designed for water submersion.

FEATURES: Side, Bottom, Top Mounting Valve body screws apart by hand for easy servicing Flow stops when unscrewed for servicing Supplied with back-nut and seal washer Built in check valve Fully adjustable Float Angle Pressure range 0-150 PSI Low pressure...

It is a thermal sensing valve that is constatly in contact with the water & "intermittently" releases enough pressurized water to prevent surface ice as the water temperature dictates.

Connects valve to 301 round float A brass rod float arm 1/4" x 1 1/2" with threads on each end.

#7 on breakdown. Pride of the Farm 5/32" Orifice on a VP124 Valve. It has O'ring on one side & a Diaphragm on the other (not included).

If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole. 8' 2" Diameter x 26" H 113# 5 Year Warranty

SPI Drain Plug (#11) for all New Generation waterers.

The Jug Basic Float Valve fits Models J101, 202, 303 & 404 with or without heat.

Black rubber seat to fit inside the Mira Fount RED Plunger in a Mira Fount cattle waterer valve.

The VS15E is constructed as a sturdy double walled foam-filled (polyurethane insulation) unit. 22" W x 27" L x 26" H 7 gal. Meets "Grade A" Dairy requirements (non-siphoning). Very efficient use of energy.