Farm Equipment Livestock Waterers For Sale In Boise City

A brass rod float arm 1/4" x 1 1/4" with threads on each end. Connects valve to 301 round float.

This two hole, 5.2 gallon waterers uses a 250 or 500 watt submersible heater and can easily ship UPS. Engineered with the farmer in mind, this waterer allows easy access to the submersible heater, water line, incoming services and provides effortless...

Thermostat ONLY for all Johnson Concrete Waterer Models.

A brass rod float arm 1/4" x 2" with threads on each end. Connects valve to 301 round float.

Filter replacement for Topaz & Megaflow Valves.

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

Turns on at 36 degrees and turns off at 48 degrees. Often used in Franklin & Arkfeld waterers. Surface mount thermostat used in galvanized waterers.

Water and electric lines run underground below frost line. The 303 Riser Tube protects the water supply line from the cold by insulating it in urethane foam, and warming it with a low wattage heating element.

20 Gallon, 36" x 35" x 25" - 1060# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

3" orange arm that fits between the lower arm and the float connect. This piece is held by two thumbscrews not included in this part.

A Brass short arm to connect the valve and the round float in Arkfeld and SPI waterers.

Saves money by using power only when temperatures require. Turns on at 35 degrees & turns off at 45 degrees. Has many uses around the home & farm. Five controlled temperatures (one just right for you) & no installation required.

Arkfeld waterer element replacement. 1000 watt x 120 volt heating element only.

The upper arm is blue and is located in the top bracket of the top base and is held by a lock pin. It moves the plunger to and from the orfice.

This repair kit will fit in all Apex Valves & is made for use in all high pressure or low pressure applications.

The polyethylene used in our SPI Livestock Waterers is FDA and HPB approved, food grade, recyclable plastic. 22" W x 27" L x 26" H 7 gal. Meets "Grade A" Dairy requirements (non-siphoning).

If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole. 37 1/4"L x 28" W x 12 3/4" H 11 # 5 year warranty

SPI 351/352 (old style) Rubber Drain Plug only .

Arkfeld waterer element & thermostat replacement. 600 watt x 120 volt heating element with surface mount thermostat included.

The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction tanks. 43 3/4" x 28 3/4" x 23" Comes with 1.25" drain installed. Available in Aqua Blue color only.

A brass rod float arm 1/4" x 6" with threads on each end. Connects valve to 301 round float.

Pride of the Farm 3/4" OD x 1/4" ID DURAPRIDE Plastic Base that screws to your water supply line. #9 on breakdown.

The orange male fitting end of the Franklin Valve. No inside working parts included.

80 Watt Immersible element used in the PC 1 waterer.

Robert's 3/4" leather cup ring that fits on the brass plunger.