Farm Equipment Livestock Waterers For Sale In Albuquerque

It has O'ring on one side & a Diaphragm on the other (not included). Pride of the Farm 1/4" Orifice on a VP124 Valve. #7 on breakdown.

15" OD, corrugated plastic tubing. Used to extend the Insulated Earth Tube into warm ground below the frost line & form the Heat Well. Corrugated design provides rigidity without bulk when back filled with earth.

A drain plug for the Arkfeld waterers - 1 1/2" in size - Black rubber.

Orange plastic valve assembly fits a 3/4" FPT with a 1/2" orfice inlet. Mostly used on Franklin hog waterers.

15" OD, corrugated plastic tubing insulated inside with Urethane foam to a 10" ID. Used to insulate the Heat Well below the frost line, preventing the loss of energy into the frozen ground.

SPI's energy free waterer is built using 100% polyethylene construction creating a strong corrosion free product to provide many years of trouble free operation. The peaked roof and raised ribs around the door openings prevent manure, feed and other contaminants...

Available in Forest Green in stock, other colors available for special order are Ash Grey, Black, Blue, Red & Tan. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction tanks.

Apex replacement float with string included.

We tested this unit in our own cold chamber. Available in light gray. Simple water level adjustment, easy to clean. Heating cost is minimal-less than $10.00 per heating season. Foam filled-R value of 7.5 per inch.

A brass rod float arm 1/4" x 4" with threads on each end. Connect valve to 301 round float.

A brass rod float arm 1/4" x 7" with threads on each end. Connects valve to 301 round float.

Available in Forest Green in stock, other colors available for special order are Ash Grey, Black, Blue, Red & Tan. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction tanks.

A round float for Arkfeld,SPI or Mira Fount waterers.

68 Gallon, 72" x 35" x 25" - 1910# All J Models Heavy duty concrete tank (reinforced with rebar and fibermesh Safe, quick and easy to lift and set Epoxy painted trough and outside Chamfered edges Notched top for controlled overflow Brass or plastic water...

15" OD, corrugated plastic tubing insulated inside with Urethane foam to a 10" ID. Used to insulate the Heat Well below the frost line, preventing the loss of energy into the frozen ground.

A brass rod float arm 1/4" x 5" with threads on each end. Connects valve to 301 round float.

SPI hatch cover for model 4x4 energy free waterer.

The orange cap only that fits over the insides of the Franklin Valve.

Pride of the Farm 5/8" O'ring that goes between the valve base & orifice on a VP124 Valve assembly. #8 on breakdown.

Half moon design on back corner for securing up to a 2 inch (5.1 cm) PVC tube for plumbing from above or below. Model VT100 valve delivers about 2 1/2 gallons (9.5 liters) per minute.

Same desription as the J202 EXCEPT THIS UNIT HAS NO HEAT!

3 year warranty. All edges have been rounded for safety & strength. If the tank gets a small leak due to unforeseen circumstances, such as a bullet hole, it can be braze welded with a common butane torch to fill the hole.

Model WP012 is loaded & is also one of the better looking drinkers ever to reach the market. Lower access opening is 6" x 19". Great value & great features don't have to come in a boring, boxy profile.

This quick release "D" clip is used on all of the New Generation Energy Free Waterers (4 per Unit) & on the Electric Waterer's inspection plates.

Available in Forest Green in stock, also available in Ash Grey, Black, Blue, Red & Tan colors for special order. The one piece construction eliminates cracking & splitting common in plastic-welded, two piece construction tanks.