Dot Overhang Regulations

In the unlikely event of regulator malfunction, the safety valve assures a safe vacuum level. Stabilvac Safety Valve is designed to work exclusively with the Stabilvac to provide safe milking vacuum.

Includes cables, paper roll, and AC transformer. 4” x 4” x 2” unit prints characters and graphics on a strip of paper.

The design allows for quick installation, and the unit can be cleaned and serviced in less than 10 minutes. This separate-style regulator, which divides the servo valve and the main control valve into two parts as shown, is recommended for vacuum pumps...

Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the Mark II vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the noise...

Two filters required. Replacement Foam Filter for 173-02010 Vacuum Regulator.

Overall dimensions 7" in diameter and 12.5" high. 3" Female NPT mounting connections. May be adjusted between 10" and 15". The Model 350 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 350 CFM ASME and features...

Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the model M100 vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the...

For Sentinel models MKII and M100. Relief Valve safeguards the system against high vacuum incidents.

The design allows for quick installation, and the unit can be cleaned and serviced in less than 10 minutes. This regulator is recommended for vacuum pumps from 12 to 35 cfm (350 to 1,000 liters/min) and will maintain vacuum from 10” to 15” Hg (36...

Tests show that the Peacekeeper can cut 10 to 15 decibels off existing noise level. The Peacekeeper for the M350 and M500 vacuum controller is a combination noise suppressor and air filter providing a large washable filter and effective reduction of the...

Part number "353-06" on schematic diagram.

Part number "348-36" on schematic diagram.

Accurate, quiet and easy to install, this Regulator reads vacuum levels up to 3000 LPM (105 CFM) . Servo-style Vacuum Regulator is ideal for pipelines or portable milking operations.

Overall dimensions 6" in diameter and 11-1/4" high. 2" Female NPT mounting connections. Featuring ABS housings and top dome and main filter, the Mark II may be adjusted between 10" and 15".

Irrigation filters can wear out and break down over the course of the season, allowing larger particles to pass into your drip tape and plug the emitters. Replacing the filter on your drip irrigation system is highly recommended before each season.

Fits Sentinel 100, 350, 500 Vacuum controllers. Part number "348-33" on schematic diagram.

Overall dimensions 7" in diameter and 12.5" high. 3" Female NPT mounting connections. May be adjusted between 10" and 15". The Model 500 Sentinel Vacuum Controller is appropriate for installations where airflow does not exceed 500 CFM ASME and features...

Repair Kit for Fullwood/BouMatic (blue) Vacuum Regulator contains gaskets, O-rings and filters.

DOS and WindowsA software isA included to allow numerical and waveform data to be named, saved and then uploaded to your computer for filing, insertion into other programs, or printing.

The design allows for quick installation, and the unit can be cleaned and serviced in less than 10 minutes. This separate-style regulator, which divides the servo valve and the main control valve into two parts as shown, is recommended for vacuum pumps...

Safety Valve for Stabilvac Seperate styles.

At 50 kPa (49 cfm at 15" Hg.) Stabilvac Vacuum Relief Valve works over a range of 36 to 50 kPa (11" to 15" Hg) and has a capacity of 1400 liter/min.

For systems with CFM's over 250, two are recommended. Relief Valve for Sentinel Controllers models M350 and M500 protects against occurrences of high vacuum. Part number "348-17" on schematic diagram.

Female to tape lock adaptor (items 40193, 40194, 40195). Main line systems by using a ¾ in. Filter housing comes with filter. Filter can be used with 1 in., ¾ in., and ½ in. Having a filter on your drip irrigation system is highly recommended as filters...

Too high or low pressure can be an early warning that something needs to be replaced, cleaned, or fixed. Use to monitor water pressure in your irrigation system. Use to replace a damaged or worn unit or to create your own drip irrigation system with our...

Too much pressure can expand the emitters or cause drip line failure, leaving you with a costly and time-intensive repair. Pressure Regulator 30 PSI. Make sure you are keeping proper pressure in your drip system so you don't blow out your drip lines.

(21-27 C.).The easiest method for growing a polka dot plant, however, is from cuttings. The leaves are dotted with darker spots in green and a base color of pink. Indirect bright sunlight is the ideal location for this plant indoors.